For more help and resources, call 1-800-544-1108 or visit www.safety1st.com
11
10
ZOOM CONTROL BUTTON (1x, 2x, 4x)
Zoom Control Button is the upper left button on the side of Parent Unit.
There are 3 levels: Zoom 1x (normal view), 2x and 4x.
To adjust zoom view , press up (+) or down (-). Zoom status will display on
screen. If no zoom icon appears on screen, press once to check current zoom
status and press twice to change zoom status.
BRIGHTNESS CONTROL BUTTON
Brightness Control Button is the upper right button on the
side of Parent Unit. To adjust brightness level, press up (+)
or down (-). Brightness level icons will display on screen.
If no brightness icon appears on screen, press once to
check current brightness status and press again to change
brightness status.
DAY/NIGHT AUTO VIEWING
Day/Night Auto Viewing lets you see your baby in a darkened room. The video
display during this time is in black and white. For best view of your baby in a
dark room, increase brightness control until desired brightness is achieved. For
best visibility, Camera should be 3 feet away from your baby.
VIDEO ON/OFF BUTTON
Video On/Off Button is on the top of Parent Unit. Press
the Video On/Off Button to shut-off the video screen. The
Video Off icon will appear. Press again to bring back full
video. When unit is battery powered, video will only stay
on for approximately 2 minutes and then it will time out to
black screen. Audio and sound lights are still enabled. This
is a battery saving feature in the product. Please note that
when Parent Unit is plugged in, video will not time out.
POWER INDICATOR
The power indicator is a green LED that indicates that the
unit is on and functioning. If LED turns red, this is a low
battery indication. See Battery Indicator paragraph.
LINK INDICATOR - OUT OF RANGE
If the unit is working and goes out of range, the no-link
icon will appear and the link indicator LED will illuminate
red. If product is detected as close to losing link, where signal
quality is losing over 50% of it's information, monitor will keep giving image,
but link indicator LED will flash red indicating that loss of link is possible.
Using Your Monitor
Using Your Monitor
Fully Charged Battery Icon
(Green/4 Bars)
Low Battery Icon
(Red/No Bars)
Use for Wall Mount
BATTERY INDICATOR
When battery is fully charged, the green battery icon
appears on screen with all four bars. As the battery
power lowers, the green bars start to go away. When
the battery icon gets to a single bar, the icon will
change to an orange color. Low battery power is
indicated when no bars appear, the icon changes to
red and will flash until the unit goes off and Power
Indicator LED changes to red.
RIGHTVIEW BELT CLIP
The Belt Clip is convenient for portability. You can clip
the Parent Unit to your belt or waistband and easily tilt
unit up to view baby without reorienting or removing
baby monitor from your waistband.
Baby Unit (Transmitter):
PROPER POSITIONING
IMPORTANT:
When choosing locations to set up the Baby Unit and Parent Unit,
follow these guidelines:
• For best sound quality, place Baby Unit 3 feet (0.9 m) away from the baby.
• Adjust volume dial on Parent Unit to appropriate level to minimize feedback.
• During use of the monitor, sound quality deteriorates as you reach the limits
of the monitor's range. If this happens, you will need to move the Parent Unit
in closer proximity to the Baby Unit.
IMPORTANT – CHECK RECEPTION
:
The first time you use your monitoring system, two adults
should test it in the following way:
• Place Parent Unit at least 20' (6m) away from Baby Unit.
• Have an adult speak into Baby Unit at various levels (soft to loud) while another
adult checks Parent Unit for the proper sound and picture reception. Try Parent
Unit in every location that it will be used.
Wall Mounting the Camera
Mounting the Baby Unit on a wall is similar to mounting a picture.
1. Make 1 mark in your desired location on the wall. Make certain location
is close to power source and any wiring is not accessible by children.
2. Install 1 screw (5/16" head) in the wall where you made the mark.
3. Carefully place base of Baby Unit on screw and gently slide to the
left until Baby Unit is securely in place. Confirm attachment to wall
before letting go of Baby Unit.
4. Plug in AC adapter. Ensure all wiring is properly positioned to
avoid all contact and/or accessibility by children. Recommend
battery power use if cable poses possible hazard.