CABINET
DRAWER
Remove adhesive cover from back of
template. Slide template onto catch.
1a
1b
1b
6
6
5
5
7
7
2
2
4
4
1” (2.5 cm)
Line up template edge
A
roughly 1 inch (2.5 cm) away
from center frame (close to
door handle).
Insert template until vertical
edge meets front of cabinet
frame.
Mark (2)
CATCH HOLES
positions with
pencil.
Screw in catch by hand using a Phillips
head screwdriver.
Remove adhesive cover from back of
template. Slide template onto catch.
Close cabinet door until contact with
adhesive is made. Open door and
ensure template adhesive has stuck.
Mark (2)
LOCK HOLES
positions with
pencil. Remove template. Do not
dispose of template as you will need to
reuse it for other installations.
Pre-drill screw holes for catch 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through cabinet underhaul. NOTE: For
best install, take a position under the
cabinet to drill holes.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
3
3
3/8” (0.9 cm)
3/8” (0.9 cm)
NOTE: Remove drawer if
possible for easier installation.
Line up template edge
A
roughly 1 inch (2.5 cm) away
from side of drawer.
Insert template until vertical
edge meets front of cabinet
frame.
Mark (2)
CATCH HOLES
positions with
pencil.
Pre-drill screw holes for catch 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through drawer underhaul. NOTE: For
best install, take a position under the
cabinet to drill holes.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
Screw in catch by hand using a Phillips
head screwdriver. Put drawer back into
cabinet.
Mark (2)
LOCK HOLES
positions with
pencil. Remove template.Do not
dispose of template as you will need to
reuse it for other installations.
Close drawer until contact with
adhesive is made. Open drawer and
ensure template adhesive has stuck.
When closing drawer, if the lock does
not engage the catch, loosen screws
and adjust the lock up or down until
lock engages. Re-tighten screws.
When installation is complete, make
sure to use the magnetic key over the
drawer to open drawer.
Position lock slots centered over
pre-drilled holes.
Screw in lock by hand
using a Phillips head screwdriver.
Pre-drill screw holes for lock 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through drawer.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
When closing door, if the lock does not
engage the catch, loosen screws and
adjust the lock up or down until lock
engages. Re-tighten screws.
When installation is complete, make
sure to use the magnetic key over the
cabinet to open door.
Position lock slots centered over
pre-drilled holes.
Screw in lock by hand
using a Phillips head screwdriver.
8
8
Pre-drill screw holes for lock 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through cabinet door.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
NOTE: If drill is too large you can use
extra force to manually tighten the
screws with screwdriver (skip steps
about pre-drilling).
NOTE: If drill is too large you can use
extra force to manually tighten the
screws with screwdriver (skip steps
about pre-drilling).
10
10
9
9
1a
1” (2.5 cm)
Center frame