background image

 

 

Safe Fire Detection –  Home Office  

 

Safe Fire Detection, Inc.  
5915 Stockbridge Drive.  
Monroe, North Carolina 
28110 USA 
 
Phone: 704-821-7920 
Fax: 

704-821-4327 

E-Mail: [email protected] 
Web Page: http://www.safefiredetection.com  

 

 
 
NOTICE: 
THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN 
EQUIPMENT, OR TO PROVIDE FOR EVERY POSSIBLE CONTIGENCY IN CONNECTION, 
INSTALLATION, 

OPERATION  OR  MAINTENANCE  OF  SAFEFLAME  FLAME

DETECTION SYSTEMS. 

 

SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS 
ARISE, WHICH ARE NOT COVERED SUFFICIE

NTLY FOR THE PURCHASERS PURPOSE , 

THE MATTER SHOULD BE REFERRED TO SAFE FIRE DETECTION, INC.  

 

INSTALLATION,  COMMISSIONING,  SERVICE  AND  MAINTENANCE  SHOULD  ONLY  BE 
PERFORMED BY SAFE FIRE DETECTION, INC. OR BY AN AUTHORIZED DISTRIBUTOR / 
REPRESENTATIVE FAMILIAR WITH ALL RELEVANT PROCEDURES AND HAZARDS. FOR 
INFORMATION 

REGARDING 

TRAINING 

SCHOOLS 

OR 

FACTORY 

APPROVED 

CERTIFICATION, PLEASE CONTACT SAFE FIRE DETECTION.  
 
 
 
 
 

Copyright Information: 
This Document may not be reproduced in whole or in part, by any means without the prior express 
written permission of Safe Fire Detection, Inc.  
 
 
 
Disclaimer: 
Safe Fire  Detection, Inc.  reserves the right to change any information contained in this manual 
without notice.  
 
 
 
Codes and Standards: 
Safe Fire Detection , Inc.  strongly recommends that this manual be read in conjunction with the 
appropriate local codes and standards for fire detection systems and electrical connections. 

 

 

 

 

                 
  
                                                                                          
                                                                                                          

 

 

SafeFlame Installation and Operation Manual 

(Publication#: MA-SF200OM)

 

Содержание SafeFlame SF200A
























Отзывы: