manualshive.com logo in svg

Safe Fleet Prime Design VBC-FT31B, Руководство по сборке, Страница: 8 / 8

Поделиться
Скачать
Safe Fleet Prime Design VBC-FT31B Скачать руководство пользователя страница 8

PRIME DESIGN, A SAFE FLEET BRAND 

▪

 Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 

▪

 Phone: 651-552-8554 

▪

 Toll Free: 1.8.PRIME.RACK 

▪

 Fax: 651-552-1799 

▪

 Email: [email protected] 

▪

 Website: www.primedesign.net

TM & © 2019 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

8

M8 Locknut

Flat Washer

M8 x 35MM

Carriage Bolt

View from vehicle front

USAM-VBCFT31B-US01 Rev-C 0419

VBC-FT31B ASSEMBL

Y 

INSTR

UCTIONS

LADDER STOPS

8.2

Torque to 90 in-lbs

8.1

Loosen nuts

NOTE:

 The orientation of 

the bolt hole faces away 

from the Crossbar

Place the Front Hook Clamp Bracket removed in Step 7.1 

into the lower groove of the Crossbar, and slide it on top 

of the Front Ladder Hook Clamp

7.3

7.4

Reassemble the Front Clamp Down Tube Holder 

using the fastening hardware removed at Step 

7.1. Do not tighten until Step 7.6

7.6

Torque to 90 in-lbs

7.5

Adjust the Front Hook until it aligns with the Rear Hook. Perfect 

alignment may not be possible in all instances, and depends 

upon the location of the Crossbar Mounting Brackets. If such 

interference should occur, align the Hook as close as possible.

Содержание Prime Design VBC-FT31B









Отзывы:

Нет отзывов