Fold Her
e
Step 2: Remove Camera Dome
1. Using the security key supplied with the camera, loosen the captive screws on the housing.
2. Lift the housing off the base.
Step 3: Connect Camera to Recorder
1. Connect the pigtail to the camera harness through the panel cable hole.
Important
: ensure the camera harness cable has a blue band in front of the connectors, indicating it is
AHD-compatible.
2.
Connect the camera harness 2x3 Microfit connector to the recorder.
CAUTION: Camera circuit board and wiring
While installing the camera, do not impact the printed
circuit board or wiring inside the camera with screws or
screwdriver bits: damage to the camera can result.
Use the two #8 x 1” (25.4mm) self-drilling mounting screws
supplied with the camera to attach the camera to the vehicle.
Step 5: Aim the Camera
1. With a monitor connected to the recorder, power up the
system. The monitor should display multiple camera views
once the recorder is powered up.
2. Double-click a camera tile image to display it in full-screen
mode.
3. Aim the camera by tilting*, panning, and rotating as required.
*
Loosen the two Phillips head tilt adjustment screws (one
on each side of the gimbal), adjust tilt as required, then re-
tighten the screws.
1
2
To video recorder
Step 7: Configuration Settings for Forward-facing Applications
For improved image quality in forward-facing camera applications (through the windshield) we recommend the
following procedure to disable infrared (IR) LEDs:
1. Right-click a recorder camera view to open the on-screen display.
2. Click
Configuration
.
3. Navigate to the Control over Coax (CoC) settings:
• If connected to a TH6 recorder
:
Record
Camera
Camera Advanced
• If connected to a TH8 or NH16 recorder
:
Record
Camera
Analog
CoC Cam Control
4. Click the tab corresponding to the recorder port number
connected to the HD2Q camera.
5. Click
Set
to display the
SETUP
menu.
6. Click
twice
to highlight
FUNC
.
7. Click
Set
to open the
FUNC
menu.
8. Click
Set
(again) open the
DAY NIGHT
menu.
9. Click
six times
to highlight
IR LED
.
10. Click
to toggle the
IR LED
setting
OFF
.
11. Click
to highlight
RETURN
.
12. Click
Set
to return to the
FUNC
menu.
13. Click
twice
to highlight
RETURN
.
14. Click
Set
to re-display the
SETUP
menu.
15. Click
twice
to highlight
EXIT
.
16. Click
Set
to open the
EXIT
menu.
17. Click
to highlight
SAVE AND EXIT
.
18. Click
Set
to save settings.
The CoC menus close in a few seconds.
Step 6: Replace Camera Dome
1. Fit the dome onto the base.
Ensure the notches on the edge of the dome and the camera
base are aligned
before tightening the security screws
.
2.
Ensure the rubber IR boot around the camera lens is firmly
pressed against the inside of the dome.
3. Use the security key to tighten the captive screws.
Routine Maintenance
Most liquid cleaners or graffiti gel can be used to clean your camera enclosure. Do not use abrasive cleaners
that can scratch the window and reduce visibility of the camera.
Replacing Damaged Dome Lid
If the dome bubble becomes scratched, cracked, or broken, please contact Safe Fleet Support to purchase a
replacement.
To remove and replace the housing, follow the procedures in "Step 2: Remove Camera Dome" and "Step 6:
Replace Camera Dome" on page 2.
Step 4: Install the Camera
#8 x 1” self-drilling
mounting screws
Alignment
notches
Pan
Tilt
Tilt adjustment
screw
Rotate
Recorder camera ports
CoC menu
controls
CoC menu
