Monitor and Camera Connections (
Standalone
)
Use the following image and steps to connect the monitor and camera:
Once the camera is installed according to its installation documentation:
1.
Connect the 2x3 Microfit connector on cable
A
to the
BACK AV3
Microfit socket on cable
B
.
2.
Install the monitor bracket and mount the monitor on the dashboard.
For details, see the
Rear Vision Monitor Quick Install Guide
(700-1107).
3.
Connect the monitor output from cable
B
to the monitor input cable.
Verify that the arrows on the connector ends are aligned.
4.
Connect the
BACK TRIGGER AV3
(blue) fly wire from cable
B
to the striped end of the supplied diode.
5.
Connect the unmarked end of the supplied diode to the reverse signal input (active high trigger).
6.
Connect the
GND
(black) fly wire from cable
B
to battery negative.
7.
Connect the
POWER
(red) fused fly wire from cable
B
to 12V ignition (switched source) power.
8.
(
Optional
) Attach the M12 socket on cable adaptor
C
to the
LEFT AV1
input on cable
B
.
The RCA jacks on cable
C
accept composite video input from an accessory device.
To use the standard definition video output (CVBS) from an inView 360 HD system, connect the adapter cable
060-1199 to an RCA input on cable
C
. For more information, visit the Seon Community
(
https://community.safefleet.net
).
9.
See “Power On and Test”.
Monitor and Camera Connections (
Recorder Integration
)
Use the following image and steps to connect the monitor, camera, and recorder:
1.
Once the camera is installed according to its installation documentation, connect cable
A
to a camera port on the
back panel of the recorder
.
Take note of the camera port number
*
- you’ll need it for the Recorder Configuration procedure
(see the
RVS
Recorder Configuration Guide
(700-1103).
*
for TL-HD recorders, note the channel number
2.
Connect the 2x4 Microfit
*
connector on cable
B
to the
EXPANSION
**
socket on the recorder’s rear panel.
*
for TL-HD recorders, use the 1x8 Sherlock connector
**
for all other supported recorders, connect to the
EXPANSION
1
socket
3.
Connect the 2x3 Microfit connector on cable
B
to the Microfit socket on cable
C
.
4.
Connect the 2x3 Microfit connector on cable
C
to the
BACK AV3
Microfit socket on cable
D
.
5.
Install the monitor bracket and mount the monitor on the dashboard.
For details, see the
Rear Vision Monitor Quick Install Guide
(700-1107).
6.
Connect the monitor output from cable
D
to the monitor input cable.
Verify that the arrows on the connector ends are aligned.
7.
Connect the
BACK TRIGGER AV3
(blue) fly wire from cable
D
to the striped end of the supplied diode.
8.
Connect the unmarked end of the supplied diode to the reverse signal input (active high trigger).
9.
Connect the
GND
(black) fly wire from cable
D
to battery negative.
10.
Connect the
POWER
(red) fused fly wire from cable
D
to12V ignition (switched source) power.
11.
(
Optional
) Attach the M12 socket on cable adaptor
E
to the
LEFT AV1
input on cable
D
.
The RCA jacks on cable
E
accept composite video input from an accessory device.
To use the standard definition video output (CVBS) from an inView 360 HD system, connect the adapter cable
060-1199 to an RCA input on cable
E
. For more information, visit the Seon Community
(
https://community.safefleet.net
).
12.
See “Power On and Test”.
Monitor trigger inputs
expect an Active H/L signal
.
Voltage references:
Active H: DC 3.3V - 36V
Active L: < DC 3.3V
Monitor trigger inputs
expect an Active H/L
signal
. Voltage
references:
Active H: DC 3.3V - 36V
Active L: < DC 3.3V