SAF CFIP Lumina Series Скачать руководство пользователя страница 81

Страница: 81 / 107

The CFIP Lumina Series Full Outdoor Unit Technical Description and Configuration Guide

•

Rev. 1.3

•

© SAF Tehnika JSC 2010

1. Shows the time during which statistics have been gathered;

Clear statistics

–

resets all statistics counters (not available for “guest”

account);

TxOctets

- The total number of good bytes of data transmitted by a port

(excluding preamble but including FCS);

TxDropPkts

- This counter is incremented every time a transmit packet is

dropped due to lack of resources (e.g., transmit FIFO underflow), or an
internal MAC sublayer transmit error not counted by either the
TxLateCollision or the TxExcessiveCollision counters;

TxQ0PKT

- The total number of good packets transmitted on COS0, which is

specified in MIB queue select register when QoS is enabled;

TxBroadcastPkts

- The number of good packets transmitted by a port that are

directed to a broadcast address. This counter does not include errored
broadcast packets or valid multicast packets;

TxMulticastPkts

- The number of good packets transmitted by a port that are

directed to a multicast address. This counter does not include errored
multicast packets or valid broadcast packets;

Содержание CFIP Lumina Series












































































































Результаты поиска

Содержание CFIP Lumina Series

Отзывы:

Похожие инструкции для CFIP Lumina Series

Бренды по названию

Популярные бренды

SAF CFIP Lumina Series, Техническое описание и руководство по конфигурации

Результаты поиска

Содержание CFIP Lumina Series

Отзывы:

Похожие инструкции для CFIP Lumina Series

Бренды по названию

Популярные бренды