Sabo 107-17 HS Скачать руководство пользователя

Страница: 49 / 68

Troubleshooting - 45

TROUBLESHOOTING

Loss of power

Cutting too much grass /too fast.

Throttle in “CHOKE” position.

Buildup of grass, leaves and trash under mower.

Dirty air filter.

Low oil/dirty oil.

Faulty spark plug.

Dirty fuel filter.

Stale or dirty fuel.

Water in fuel.

Spark plug wire loose.

Dirty engine air screen/fins.

Dirty/clogged muffler.

Loose or damaged wiring.

Carburetor out of adjustment.

Engine continues to run when operator leaves seat

Faulty operator-presence safety switch.

Engine Backfires When Turning Engine “OFF”

Engine throttle control not set at “SLOW” position for 30 seconds
before stopping engine.

Engine will not turn over

Clutch/brake pedal not depressed.

Attachment clutch is engaged.

Weak or dead battery.

Blown fuse.

Corroded battery terminals.

Loose or damaged wiring.

Faulty ignition switch.

Faulty solenoid or starter.

Faulty operator presence switch.

Headlight not working

Bulb(s) burned out.

Loose or damaged wiring.

Blown fuse.

Battery will not charge

Bad battery cell(s).

Poor cable connections.

Faulty regulator/rectifier.

Mower blades will not rotate

Obstruction in clutch mechanism, or blades.

Worn/damaged mower drive belt.

Frozen idler pulley.

Frozen blade mandrel.

CHECK

Содержание 107-17 HS





































































Результаты поиска

Содержание 107-17 HS

Отзывы:

Похожие инструкции для 107-17 HS

Бренды по названию

Популярные бренды

Sabo 107-17 HS, Руководство оператора

Результаты поиска

Содержание 107-17 HS

Отзывы:

Похожие инструкции для 107-17 HS

Бренды по названию

Популярные бренды