Stabilizers screws [MH108]:
Insert 1 flat head screw M6x20mm in the front hole
•
without tightening.
Insert 1 flat head screw M6x16mm in the rear hole
•
without tightening.
Proceed to tighten the screws.
•
Match the fuselage [MH112]:
Insert 1 socket head screw M6x20mm and
•
1 washers 6.2x 9.9 x 1 mm in each hole
without tightening.
Proceed to tighten the screws.
•
Match the fuselage [MH112]:
Insert the two Socket head screws M6x20mm and the two washers
•
6.2x 9.9 x 1mm in the holes without tightening.
Proceed to tighten the screws.
•
Front wings screws:
873 [MH119]:
Insert 1 flat head screw M6x45mm in the rear hole without
•
tightening.
Insert 1 M6x50mm in the front holes without tightening.
•
Proceed to tighten the screws.
•
790 [MH124]:
Insert 1 flat head screw M6x35mm in the central hole without
•
tightening.
Insert 1 M6x30mm in the rear and front holes without
•
tightening.
Proceed to tighten the screws.
•
720 [MH109]:
Insert 1 flat head screw M6x25mm in each hole without
•
tightening.
Proceed to tighten the screws.
•
633 [MH114]:
Insert 1 flat head screw M6x30mm in each hole without
•
tightening.
Proceed to tighten the screws.
•
679 [MH109]:
Insert 1 flat head screw M6x30mm in each hole without
•
tightening.
Proceed to tighten the screws.
•
Board connection:
Insert the proper screws for the board from the upper side.
•
Check that all screws are inside the bushing before tightening.
Proceed to tighten the screws.
•
WARNING
SABFOIL provides a standard deep tuttle 16mm thick, before
•
completing the final assembly please read instruction
carefully:
I) BE SURE THAT THE TUTTLE HEAD MATCHES PERFECTLY WITH YOUR
TUTTLE BOX: If the box of your board is thinner than the tuttle head
you may need to sand the head to ensure it fits perfectly in the
box.
II) Conversely you may need to add a spacer to the tuttle head if
the box is too large.
CHECK THAT THE 2 TUTTLE SCREWS ARE THE CORRECT LENGHT FOR
•
THE THIKNESS OF YOUR BOARD
CHECK THAT THE THREAD ON THE TWO BRASS BUSHINGS IS IN LINE
•
WITH THE CORRESPONDING HOLES BEFORE INSERT THE SCREWS
66,50
155,70
52,00
134,50
80°
80°
Mast:
Fuselage:
-Insert the two socket head screws M6x20mm and the
two washers code [MH112] in the holes without
tightening.
-Proceed to tighten the screws.
Front wing 900:
-Insert the three flat head screw M6x25mm
code [MH109] in the holes without tightening.
-Proceed to tighten the screws.
wind foil manual
2
Lithium grease
[MHW033]
-Insert the proper M6 inox screws for the board from the
upper side. Check that all screws are inside the bushing
before tightening.
-Proceed to tighten the screws.
Always keep the threaded holes and every connection between carbon
(mast and wings) and aluminum (fuselage) clean and greased with
"lithium grease" [MHW033] to avoid and prevent oxidation and corrosion
due to salt water.
Check the latest version of this manual
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 Nm
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 Nm
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 N
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 N
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 N
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 Nm
THE SCREWS MUST BE TIGHTEN BETWEEN 8 AND 9 Nm
