Vehicle Pulse Rate Set Up:
User Functions:
Page 3/4
Page 2/4
For further assistance email: [email protected]
Note:
The programming button must be connected to the back of the gauge and mounted in a location
that is easy to reach to access all functions.
Park Lights
OFF
Day Brightness (D)
Night Brightness (N)
Day Color (D)
Peak readings are cleared.
Red
Blue
Green
Amber
Park Lights
OFF
Night Color (N)
Park Lights
ON
Park Lights
ON
1 2 3 4 5
Dark Bright
1 2 3 4 5
Dark Bright
Buzzer
Fast beep
Slow beep
User Functions
Exit
Gauge will exit after 5 seconds of no activity.
Ignition
ON
cl8
Press Button
Hold Button
Press Button
Hold Button
Press Button
Press Button
Hold Button
Hold Button
Press Button
Press Button
Cycle
Purple
White
Aqua
Ice Blue
Colors
bp
Brightness
Buzzer type
hb
Buzzer levels
ob
Buzzer high
Buzzer low
Buzzer off
Hold Button
VO - (0)
VO - (1)
VO - (2)
VO - (3)
Buzzer medium
Press Button
ac
Release button and press again to set display type for gauge start up and
shutdown.
Hold Button
AC - (1)
AC - (2)
AC - (3)
Open/close type
Speed Warning
Hold Button
Release button then press and hold to set
Speed
warning value.
(Speed warning range - 40 > 211 km/h)
Press Button
Hold Button
O
Peak
Od Display
Hold Button
88
Release and press button again to choose from 3 odometer display types.
Press Button
Pink
Orange
Off
Red
Blue
Green
Amber
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Use Free mode (F00) if vehicle pulse rate is unknown.
Setting Free mode:
Select (F00) > Press
and hold button until display shows (FrE) > Drive vehicle to 60km/h and press button once > Speed
pulse has been set.
km/h
PULSE SET
Hold Button
Release Button
Gauge will return to main
window after 5 seconds.
km/h
Ignition
ON
To adjust Vehicle
Pulse Rate.
Press button once to
select pulse rate.
2
4
8
16
Pulse Set
-use free pulse setting if all other settings
are out of range
- Additional troubleshooting notes:
Problem:
“Free pulse setting used but speed reading is still out”
-
If your speed reading is still out, instead of pressing the programming button at 60 KM/H, try
pressing it a 58 KM/H or 62 KM/H. This method will help fine tune your speed reading but may not
work on some vehicles.
Problem
Possible Cause
Solution
Troubleshooting:
-gauge not reading
-reading erratically
-bad connection on gauge
-test for power at the back of the gauge
-no back lighting
-incorrect wiring
-refer to fitting instructions
Please note:
If you are having problems with the installation of this product, please do not
contact your retailer or SAAS until you have read
ALL
the troubleshooting notes below.
-gauge reading is out
-wrong pulse setting
-change pulse setting and retry
-wrong VSS wire
-refer to vehicles workshop manual for
correct wire
-wrong pulse setting
WARNING!
SAAS strongly recommends that you have help with this part of the setup!
⚠
Scale Type
s8
Release and press button again to choose from 3 types of display scales.
So - (1)
So - (2)
So - (3)
Trip A - (1)
Trip B - (2)
Odometer - (3)
0
f00
F00 (Free mode)
0
Unit Set: km/h - MPH
Setting speed unit:
Press and hold programming button > turn ignition on > release button and
press again to change speed unit from km/h to MPH > gauge will return to main screen after 5
seconds > programming done.
Odometer Input Setting:
Resetting Trip A/B meter:
Press and hold programming button for 3
seconds to reset trip meter from the main screen.
Setting odometer:
Press and release programming button until (
od
) is displayed > press and
hold button until (
odo
) is displayed > release button then press and hold until first digit flashes >
release button and press again to change first digit > press and hold button to move to next digit
and repeat steps > gauge will exit after 5 seconds of no activity.
-weak VSS or bad VSS signal
-VSS signal wire may need a resistor or
diode to rectify voltage or pulse
