background image

32 025 604 15

Saab 9-3 5D M06-

52 Lift the bumper shell and thread in the wiring

harness. Fit the rubber grommet.

53 Guide the bumper shell's tabs in under the

holders. 

54 Position the bumper shell's front corner between

the wing liner and holder. Make sure that the
shell lug is between the wing liner and the holder
for the bumper shell. 

55 Fit the screws at the wing liners. 
56 Plug the connector to the connector under the

REC.

57 Check that the rubber grommet is fitted

correctly.

58 Raise the car.
59 Fit the spoiler's centre nuts.
60 Lower the car and check the fit of the bumper

shell. Adjust as necessary.

61 Close the tailgate.
62 Connect the diagnostic tool, select car and

model year, select “All”, select “Add/Remove”,
select the accessory and then “Add”.

63 Turn the ignition key to the “ON” position and

check all functions affected by the change of
wiring harness (light clusters, luggage compart-
ment locking, rear wiper etc.).

64 With the ignition key in the ON position and

reverse gear engaged, check that the system
warns against objects in the rear by using tones.
The first tone is given when an object is at a dis-
tance of 1.8 metres. The signal then has a fre-
quency of 2 tones per second, but the number of
tones per second increases the closer the object
becomes to the vehicle and changes as follows:

·

1.8 - 1.3 m: 2 tones/second

·

1.3 - 0.9 m: 3 tones/second

·

0.9 - 0.3 m: from 5 to 12 tones/second in close
stages

·

0.3 m: continuous tone

WARNING

The wiring harness must be routed and secured
so that it cannot become trapped or chafe against
anything when refitting dismantled parts. Incorrect
routing could cause damage to the wiring harness
and short circuit/fire.

F930A417

56

59

59

52

55

55

53

Содержание 32 025 603
















Отзывы: