S.R.Smith WetDek Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 15

S.R.Smith WetDek Скачать руководство пользователя страница 8

8

OPTIONAL INSTALLATION ADD-ONS

The following items are not provided with your WetDek kit but can be purchased additionally from
many local suppliers.

1. ADDITIONAL GLOBE

VALVES: To help
control the height of
each individual zone it
is required that a 1”
Globe Valve (5) be
placed after each 1”
HPV Valve (3) as
shown in

FIGURE 8

.

This allows the WetDek
to be customized even
more. Water heights
can be set to the exact
same level or setup on
a tiered system that
separates each zone by
measured increments.

2. SPIGOT FOR STAND

ALONE: A spigot can be
incorporated in the stand
alone version of the WetDek
to allow for draining the
reservoir, as shown in

FIGURE 9

; this spigot

should be located between
the pump (8) and
filter/chlorinator (9). The
spigot must be easily
accessible to allow for
connection to a hose. No
spigot is required for the
poolside version because
the pool will have its own
drain system.

3. UNION FITTINGS: It is also

a good idea to use union
fittings before and after
each piece of equipment
used in the WetDek system
to allow for easy repair or
replacement. This is also
shown in

FIGURE 9

.

FIGURE 8

FIGURE 9

«
...
6
7
8
9
10
...
»

Содержание WetDek
















Отзывы:

Нет отзывов