background image

13

W i r e l e s s   R e m o t e   O p e r a t i o n

The new poolLUX

®

 Plus wireless remote system is shipped ready to use and requires no additional 

programming. In the event that another poolLUX

®

 Plus or similar device is operating on the same 

pairing code, then an alternative code will need to be selected via the 4 position DIP switch inside 
the battery compartment of the remote. The receiver board inside the control panel will also need 
to be changed to match the new remote settings.  
See Pairing Code chart below for additional details.

Note:

 The default code as shipped is Code A on both the 

remote and the receiver.  

Sleep Mode

To conserve battery power, the remote will enter standby mode 
when no function has been selected for 30 seconds or more.  To 
wake the remote, simply press the ‘1’ or ‘S’ button momentarily.  
The indicator will light up solid for 5 seconds indicating that 
it is ready to transmit. A rapidly flashing light from the LED 
indicator that is located between the two command buttons 
indicates that a command signal was sent to the control panel.  

To Turn On Using the Wireless Remote

Wake the remote out of Sleep Mode, press the (1) button to 
turn the system ON/OFF.

Note:

 The rocker switch on the poolLUX

®

 Plus must be set  

to REMOTE for wireless operation.

Color Changing Operation

To change pool light colors, simply toggle the (1) button ON/
OFF within 1 second.  Continue toggling until the desired color 
or light show is reached.

1-Button - Color Sync / Reset Operation

(For use only with SR Smith LED Treo, FG, Treo Micro &  
LED water features)

To color synch lights in a multi-light installation, simply press 
the “S” button once and wait 15 seconds.  During this time,  
the lights will flash on and off several times, pause in the OFF 
mode, then reset to color mode 1 (soft color change).

Performance Note:

 For best results, hold the remote  

vertically (pointed at the sky) when pressing the  
command buttons.

PAIRING CODE CHART

DIP Switch

1

2

3

4

Code A

OFF OFF OFF OFF

Code B

ON OFF OFF OFF

Code D

OFF ON OFF OFF

Code C

ON ON OFF OFF

Code E

OFF OFF ON OFF

Code F

ON OFF ON OFF

Code G

OFF ON ON OFF

Code H

ON ON ON OFF

Code I

OFF OFF OFF ON

Code J

ON OFF OFF ON

Code K

OFF ON OFF ON

Code L

ON ON OFF ON

Code M

OFF OFF ON ON

Code N

ON OFF ON ON

Code O

OFF ON ON ON

Code P

ON ON ON ON

Содержание poolLUX Plus pLX-PL60

















Отзывы: