Ryobi VC30ARG, Руководство по эксплуатации для владельца, Страница: 13 / 16

3
PACKAGING CONTENT
See Figure 1-3.

Carefully unpack the contents of the box.
 Hold the two clamps, which hold the upper section in
its position and fold them upwards.
 Loosen the clamps, remove the upper section, and
remove the contents from the tank.

Please check the parts using the components list to
make sure they are complete and that there has been
no damage in transport.
 If any parts are missing or damaged, then please
contact your dealer immediately
ASSEMBLY
 Make sure that the connector is not plugged in.
 Hold the two clamps, which hold the upper section in
its position and fold them upwards. See figure 2.
 Loosen the clamps and lift the upper section up and
out. See figure 3.
 Remove the contents from the tank and turn the tank
over.
ROLLER ASSEMBLY
VC30A RG
 Put the four rollers in the guides on the bottom of the
tank. See figure 4.
 Check that the rollers have been pushed completely
into the guides.
 Fasten the rollers with four accompanying screws.
See figure 5.
VC30HDA RG , VC60HDA RG
 Insert the two small rollers into front roller guides,
ensuring they are pushed all the way in. See figure 6.
 Insert the rear axle into the rear support bracket. Slide
washer and wheel on the shaft. Insert the lock pin into
the hole on the end of the shaft to lock the wheel. Snap
the hub cap onto the wheel. Repeat the same steps at
the other end of the shaft. See figure 7.
REAR HANDLE ASSEMBLY: VC60HDA RG
 Insert the rear handle into handle guides located in
tank side. See figure 8.

Hook the accessory bag onto rear handle. See figure
9.
FILTER ASSEMBLY
 Insert the foam filter that has been supplied for wet
vacuuming. See the "WET VACUUM CLEANING"
section.
 Insert the dust bag that has been supplied for dry
vacuuming. See the "DRY VACUUM CLEANING"
section.

Replace the upper section on the tank. See figure 10.
 Align the upper section with the clamps. See figure 11.
 Hook the clamps into the upper section and let them
snap into place by pressing the clamps downwards.
 Place the large end of the hose on the front air intake
stub on the tank. See figure 12.
 Select a nozzle or the wand and slide it over the
vacuum hose. See figure 13.
 After using and cleaning the appliance, store the
accessories by attaching them to the corresponding
holders on the vacuum cleaner. See figure 14.
OPERATION
SWITCHING ON/OFF
See Figure 15.
■ Connect the mains plug.
■ Switch on the vacuum cleaner: Press and .
■ Switch on the electrical appliance and vacuum cleaner:
Press and .
■
Maximum rating power limit to electrical socket outlet of
the appliances:1000W
■ Switching on the electrical appliance automatically
switches on the vacuum cleaner. Once the electrical
appliance has been switched off, the vacuum cleaner
switches off following a time lapse.
■ Switch off the vacuum cleaner:
Press .
DRY VACUUM CLEANING
WARNING
It is absolutely necessary for you to read, understand,
and observe the section entitled "Safety Information
and Warnings".
 Never vacuum up hazardous materials. If an incorrect
dust bag is used, then the guarantee becomes void.
 Make sure that the appliance is not plugged into the
power mains.
 Make sure that the foam filter is clean and dry and
installed over the filter basket. See figure 16.
 Slide the dust bag over the hose connection in the
tank. Press it until it snaps firmly into place. In the
process, make sure that the dust bag is not damaged.
See figures 17 - 18.
 Place the upper section on the tank once again and
close the clamps. See figures 10 - 11.
 Place the large end of the hose on the front air intake
stub on the tank. See figure 12.
 Select a nozzle or the wand and slide it over the