Ryobi VC20HDRG, Руководство по эксплуатации для владельца, Страница: 8 / 11

2
to become void.

Check the float often.

If you notice liquid leaking from your appliance, switch
it off immediately and unplug it.

Do not submerge the appliance in water. Make sure
that water is not spilled on the appliance.

When disposing of the wastewater, make sure that
you observe any legal regulations.

Only store the appliance in a safe and dry location
outside the reach of children.

Please also pay particular attention to the following
“Special Safety Rules”.

This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

Children should be supervised to ensure that they do
not play with the appliance.

If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
SPECIAL SAFETY RULES

Never vacuum up hot ashes, pointed or sharp objects.

Never use the appliance in damp rooms.

Don’t use the appliance without a dust bag (an
exception is wet vacuuming or with the cartridge
filter).� Make sure that the dust bag is inserted into the
appliance correctly.

When using the appliance, make sure that no hair,
clothing, or members are drawn in.

Keep the vacuum cleaner away from heat sources
such as radiant heaters, ovens, and so on.
DISPOSAL INFORMATION

The appliance contains electric and electronic
components and may not be disposed of as household
garbage.

The local and currently applicable legislation must be
observed unconditionally.
SPECIFICATIONS
Supply voltage: 230 V - 240 V ~ 50 Hz
Maximum power: 1250 W
Tank volume: 20 L Inox
Hose system: 35 mm Ø
Filter - dry: Paper bag
Filter - wet: Foam
fi
lter
PACKAGING CONTENT
See Figures 1 - 3.

Carefully unpack the contents of the box.

Hold the two clamps, which hold the upper section in
its position and fold them upwards.

Loosen the clamps, remove the upper section, and
remove the contents from the tank.

Please check the parts using the components list to
make sure they are complete and that there has been
no damage in transport.

If any parts are missing or damaged, then please
contact your dealer immediately.
ASSEMBLY

Make sure that the connector is not plugged in.

Hold the two clamps, which hold the upper section in
its position and fold them upwards. See figure 2.

Loosen the clamps and lift the upper section up and
out. See figure 3.

Slide the handle onto the upper section from the top.
Make sure that the guide of the handle fastener is
inserted on the right side in the handle holder. See
figure 4.

Fasten the handle to the upper section with the two
accompanying screws. See figure 5.

Turn the tank over so that the upper section is on the
bottom.

Put the four rollers in the guides on the bottom of the
tank. See figure 6.

Check that the rollers have been pushed completely
into the guides.

Fasten the rollers with four accompanying screws. See
figure 7.

Insert the foam filter that has been supplied for wet
vacuuming. See the "Wet Vacuuming" section.

Insert the dust bag that has been supplied for dry
vacuuming. See the “Dry Vacuuming” section.

Replace the upper section on the tank. See figure 8.

Align the upper section with the clamps. See figure 9.

Hook the clamps into the upper section and let them
snap into place by pressing the clamps downwards.

Place the large end of the hose on the front air intake
stub on the tank. See figure 10.

Select a nozzle or the wand and slide it over the
suction tube. See figure 11.

After using and cleaning the appliance, store the
accessories by attaching them to the corresponding
holders on the vacuum cleaner. See figure 12.