![background image](http://html1.mh-extra.com/html/ryobi/vc-50hd/vc-50hd_owners-operating-manual_1507377010.webp)
9
WET VACUUMING
■
Ensure that the power cord is disconnected from the
power outlet.
Ensure that the tank is clean and free of dust and dirt.
■
Remove the cartridge filter and dust bag, and install a
back on the tank (Fig. 10).
■
Fit the desired nozzle to the vacuum hose (Fig. 13).
■
Ensure that the switch is in the ‘O’ (OFF) position before
plugging the power cord into the power outlet.
■
Turn the motor on by flipping the switch to the “I” (ON)
position (Fig. 15).
■
unplug the power cord, then empty and dry the tank (Fig.
17, Fig. 18).
IMPORTANT!
When vacuuming large quantities of liquids, do not immerse the
nozzle completely in the liquid; leave a gap at the tip of the nozzle
-
tion when the container reaches its maximum capacity. You will
notice an increase in motor speed.
When this happens, turn off the machine, disconnect from power
supply, and drain the liquid into a suitable receptacle or drain.
To continue vacuuming, refit the container with the drain cap.
After wet vacuuming, turn the machine off and remove plug from
power supply.
Empty the container, clean and dry the inside and outside before
storage.
BLOWER OPERATION
This Wet/Dry Vac has blowing capabilities.
To use the blower feature follow the instructions listed.
■
Insert the large end of the hose into the blower connection in
the top of the motor housing (Fig. 20).
■
Fit the crevice to the vacuum hose (Fig. 21).
■
Ensure the power switch is turned off and plug in the power
supply.
■
(Fig. 15).
WARNING
The foam filter must be removed after wet vacuum-
vacuuming again.
WARNING
Always wear safety goggles before using blower.
■
The unit will now blow through the vacuum hose and can be
used to clear obstructions within the hose.
■
Once you have finished operation, flip the switch to the ‘O’
(OFF) position and unplug the power cord from the power out-
let. (Fig. 16)
MAINTENANCE
INSTALLING AND CLEANING THE DRY FILTER
NOTE:
Unplug machine from the power outlet before performing
maintenance.
Installing Dry Filter
■
until it stops against the power head. (Fig.22 & 23)
■
and tighten down by turning retainer clockwise, do not over
tighten. (Fig. 24 & 25)
Removing And Cleaning Dry Filter
■
anticlockwise.
■
■
Clean the cartridge filter by gently tapping or brushing dirt
off. For optimal performance it is recommended to regularly
■
INSTALLING AND CLEANING THE FOAM FILTER
NOTE:
Unplug machine from the power outlet before performing
maintenance.
Installing Foam Filter
■
-
■
the whole cage is covered. (Fig. 10 & 27)
Cleaning Foam Filter
■
Use a mild soap and water solution to wash foam filter and
rinse with clean water. (Fig. 29)
WARNING
Ensure that you read, understand, and apply the safe
-
ty instructions.
Reminder: DO NOT vacuum hazardous substances.
WARNING
If after a few seconds the hose continues to be blocked,
turn off the unit and clear the hose manually.
WARNING
Keep bystanders clear from blowing debris.
WARNING
Wear a dust mask if blowing creates dust that might be
inhaled.
foam filter over the filter basket and place the top section
DO NOT use the cartridge filter for wet or sharp materials.
After use,flip the switch to the“O” position(Fig. 16) and
19
2180W.
6
8
Содержание VC-50HD
