Ryobi TSS100L Скачать руководство пользователя

Страница: 17 / 36

ASSEMBLy

TO INSTALL / REPLACE THE BLADE

See Figures 14 - 15.

WARNING:

A 10 in. blade is the maximum blade capacity of the saw.

Never use a blade that is too thick to allow outer blade

washer to engage with the flats on the spindle. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from secur-

ing the blade on the spindle. Either of these situations

could result in a serious accident and can cause serious
personal injury.



Unplug the saw.



Remove screws. Rotate lower blade guard and blade bolt

cover up and back to expose the blade bolt.



Depress the spindle lock button and rotate the blade bolt

until the spindle locks.



Using the wrench provided, loosen and remove the blade

bolt.

NOTE: The blade bolt has left hand threads. Turn blade
bolt clockwise to loosen.



Remove the flat washer and the outer blade washer.

not remove the inner blade washer.



Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before

placing blade on spindle. Failure to do so could cause an

accident since blade will not tighten properly.



Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as
shown in figure 15.



Replace the outer blade washer and the flat washer.

Double “D” flats on blade washers align with flats on
spindle.



Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt
counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and the
arrow printed on the side of the blade pointing down at
the front of the saw. The direction of blade rotation is also
stamped with an arrow on the upper blade guard.



Tighten blade bolt securely.



Replace the lower blade guard and blade bolt cover.



Replace screws and tighten securely.

Fig. 15

lower

Blade

Guard

Blade

outer Blade

waSher

with douBle

“d” FlatS

Blade

Bolt

tiGhten

looSen

ScrewS

Flat(S)

on SPindle

Blade

Bolt

coVer

SPindle lock

Button

Fig. 14

inner Blade

waSher with

douBle “d”

FlatS

note: BeFore uSe,

rePlace ScrewS and

tiGhten SecurelY

to PreVent Guard

MoVeMent

Blade

Bolt

outer

Blade

waSher

Blade

inner

Blade

waSher

Flat

waSher

Содержание TSS100L





































Результаты поиска

Содержание TSS100L

Отзывы:

Похожие инструкции для TSS100L

Бренды по названию

Популярные бренды

Ryobi TSS100L, Руководство оператора

Результаты поиска

Содержание TSS100L

Отзывы:

Похожие инструкции для TSS100L

Бренды по названию

Популярные бренды