Ryobi TS1552LA Скачать руководство пользователя страница 29

Страница: 29 / 34

OPERATION

wrong

WARNING:

To avoid a kickback and to avoid serious personal injury,
never position the concave edge of bowed or warped
material against the fence.

CLAMPING WIDE WORKPIECES

See Figure 42.

When cutting wide workpieces, such as in. x 6 in., boards
should be clamped with a C-clamp as shown in figure 4.

Bevel

Angle

Type of Cut

Setting

Left side, inside corner

1. Top edge of molding against fence
. Miter table set right 31.6°
3. Save left end of cut

Right side, inside corner

1. Bottom edge of molding against fence
. Miter table set left 31.6°
3. Save left end of cut

Left side, outside corner

1. Bottom edge of molding against fence
. Miter table set left 31.6°
3. Save right end of cut

Right side, outside corner

1. Top edge of molding against fence
. Miter table set right 31.6°
3. Save right end of cut

33.85°

Fig. 4

CUTTING WARPED MATERIAL

See Figures 40 - 41.

When cutting warped material, always make sure it is posi-
tioned on the miter table with the convex side against the
fence as shown in figure 40.
If the warped material is positioned the wrong way as shown
in

figure 41, it will pinch the blade near the completion of

the cut.

Fig. 40

rIght

wIde

board

Fig. 41

Содержание TS1552LA



































Результаты поиска

Содержание TS1552LA

Отзывы:

Бренды по названию

Популярные бренды

Ryobi TS1552LA, Руководство оператора

Результаты поиска

Содержание TS1552LA

Отзывы:

Бренды по названию

Популярные бренды