Ryobi SP-1218, Руководство по эксплуатации для владельца

Страница: 4 / 8

3
SPECIFIC SAFETY RULES FOR POLISHER
WARNING!
5. Never start a tool when its rotating component is in
contact with the workpiece.
6. Never lay a tool down before its moving parts have
come to a complete stop.
7.
ACCESSORIES: The use of accessories or
attachments other than those recommended in these
instructions might present a hazard.
8.
REPLACEMENT PARTS: When servicing use only
identical replacement parts.
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the voltage
marked on the name plate.
2. Never use the tool if its cover or any bolts are missing. If
the cover or bolts have been removed, replace them
prior to use. Maintain all parts in good working order.
3. Always secure tools when working in elevated positions.
4. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
1. Disc base
2. Spindle lock button
3. Auxiliary handle
4. Speed selector
5. Lock-on button
6. Soft grip handle
7. On/Off switch trigger
8. Air vents
9. Carbon brush cover
The hand held electrirc polisher is suitable for non-profes-
sional use. Any other use other than polishing and light
sanding is strictly forbidden.
Auxiliary handle, Disc base, Wool bonnet, Hex key .
WARNING! Please read and understand this operating
manual before use and keep it for your future reference.
Your power tool should only be passed on together with
these instructions.
1. Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels and
other accessories running over rated speed can fly apart
and cause injury. All the accessory must have a
maximum safe operating speed greater than the “no
load RPM” marked on the tool’s nameplate.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live”
and shock the operator.
3. Always use auxiliary handle for maximum control over
torque reaction or kick-back. Operation of the polisher
without the side handle could cause loss of control of the
grinder, resulting in possible serious personal injury.
4. Wear proper apparel while using a sander. Face shield
or at least safety goggles, dust mask, leather gloves and
shop apron capable of stopping small wheel or
workpiece fragments.
5. Position the cord clear of the spinning wheel or any
other sanding accessory. Do not wrap the cord around
your arm or wrist. If you lose control and have the cord
wrapped around your arm or wrist it may entrap you and
cause injury.
6. Regularly clean the tool’s air vents by compressed air.
Excessive accumulation of powdered metal inside the
motor housing may cause electrical failures.
7. When sanding chemically pressure treated lumber, paint
that may be lead based, or any other materials that may
contain carcinogens, use special precautions. A suitable
breathing respirator must be worn by all personal
entering the work area. Work area should be sealed by
plastic sheeting and persons not protected should be
kept out until work area is thoroughly cleaned.
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals
are:
• Le ad from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
DESCRIPITION
SPECIFICATIONS
APPLICATIONS
STANDARD ACCESSORIES
Voltage
Power input
No load speed
Disc size
Spindle size
Net weight
230V~50Hz
1200W
800-3200min
-1
180mm
M14
2.55kg
10. Allen key
OPERATION
AUXILIARY HANDLE(Fig.1)
WARNING!
Attach the auxiliary handle (3) to the tool and secure with
two hex bolts using Hex Key. Slide the hex key through the
hole (A) to access the bolt on the long side of the handle.
The auxiliary handle should be used at all
times to maintain complete control of the tool.