Ryobi RLT30CDNB Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

Ryobi RLT30CDNB Скачать руководство пользователя страница 11

GB

E

E

GB

TROUBlESHOOTInG

IF THESE SOlUTIOnS DO nOT SOlVE THE PROBlEM, COnTaCT YOUR aUTHORISED SERVICE DEalER.

PROBlEM

POSSIBlE CaUSE

SOlUTIOn

Bump knob hard to turn.

Screws threads dirty or

Clean threads and lubricate with grease - if no

damaged.

improvement, replace bump knob.

Lubricant drips from muffler.

1. Operating trimmer at

1. Operate trimmer at full throttle.

part throttle.

2. Check lubricant/fuel mixture. 2. Use fresh fuel and the correct synthetic 2-stroke

lubricant mix.

. Air filter dirty.

. Clean per instruction in Maintenance Section.

10

English

NOTE:

If your unit exhibits specific performance problem(s) where the Troubleshooting section recommends a clockwise screw

adjustment on the carburetor and no adjustments have been made since original purchase, the unit should be taken to

an authorised service centre for repair. In most cases, the needed adjustment is a simple task for the trained service

representative.

«
...
9
10
11
12
13
...
»

Содержание RLT30CDNB























Отзывы:

Нет отзывов