background image

Page 8

TO INSTALL FLUSH CUTTING BLADES

See Figures 6 and 7.

Flush cutting blades should be used when making close or
flush cuts to walls.

Plug your reciprocating saw into power supply source.

Depress and release the switch trigger of your saw in
quick, short starts and stops until blade clamp is in its full
rear position. 

See Figure 6.

UNPLUG YOUR SAW.

WARNING:

Failure to unplug your saw could result in accidental
starting causing serious injury.

Using the 5/32 in. allen wrench provided with your saw,
loosen the blade clamp screw and remove regular saw
blade.

Tighten blade clamp screw securely. Do not overtighten
screw or use an aid with allen wrench.

Loosen set screw and turn base assembly clockwise 90

°

.

See Figure 7.

Align in desired notch, then tighten set screw securely.

Remove allen wrench and store it in allen wrench holder.

Insert flush cutting blade on top of blade clamp as shown
in figure 6.

Align hole in blade shank with pin on blade clamp.

Using the flat head screw provided, secure blade to blade
clamp. 

See Figure 6.

Tighten flat head screw securely.

GENERAL CUTTING

See Figure 8.

Hold your saw firmly in front of and clearly away from you.
Make sure saw blade is clear of any foreign material and that
power cord and extension cord are out of the blade path. Be
sure material to be cut is held firmly. Small work pieces should
be securely clamped in a vise or with clamps to the work
bench or table. Mark the line of cut clearly. Depress the trigger
switch starting the cutting action, set the base assembly
against the work, then move the blade into the work. DO NOT
FORCE.
 Use only enough pressure to keep the saw cutting.
Let the blade and saw do the work.

PLUNGE CUTTING

See Figure 9.

Mark the line of cut clearly. Choose a convenient starting
point inside the area to be cut out and place the tip of the blade
over that point. Rest front edge of base assembly on work and
hold firmly in position. NOTE: Make sure blade does not
touch work until motor reaches full speed, since this could
cause loss of control resulting in serious injury. With saw
blade at full cutting speed, slowly tilt saw downward until tip
of blade starts cutting work. After blade penetrates work, tilt
saw until blade is perpendicular to the work.

Fig. 8

OPERATION

FLUSH

 CUTTING NOTCHES

BLADE

CLAMP

BLADE CLAMP IN

FULL REAR POSITION

BASE ASSEMBLY IN

REGULAR CUTTING POSITION

Fig. 6

Fig. 7

PIN

FLAT

HEAD SCREW

FLUSH

 CUTTING BLADE

BASE ASSEMBLY IN FLUSH

CUTTING POSITION

SET

SCREW

Содержание RJ150V-02















Отзывы: