Ryobi RCS-3540C Скачать руководство пользователя страница 21

Страница: 21 / 22

Problem

Possible Cause

Solution

Bar and chain running
hot and smoking.

Chain oil tank empty.

Chain tension is too tight.

Oiler is not functioning.

Clogged oil passages.

Oil tank should be fi lled every time fuel tank is fi lled.

Tension chain per instructions in Adjusting the Chain Tension in
the

Maintenance

section of this manual.

Run at half throttle 30 to 45 seconds. Stop saw and check for oil
dripping from guide bar. If oil is present, the chain may be dull or
bar may be damaged.

Remove the clutch cover and guide bar plate and clean oil passages
with a stiff-bristle brush.

E n g i n e s t a r t s a n d
runs, but chain is not
rotating.

Chain brake is engaged.

Chain tension is too tight.

G u i d e b a r a n d c h a i n
assembled incorrectly.

Guide bar and/or chain are
damaged.

D r i v e s p r o c k e t t e e t h
damaged

Release chain brake. Refer to Operating the Chain Brake in the

Operation

section of this manual.

Tension chain per instructions in Adjusting the Chain Tension in
the

Maintenance

section of this manual.

Refer to Replacing the Guide Bar and Chain in the

Maintenance

section of this manual

Inspect guide bar and chain for damage.

Contact an authorized service center for drive sprocket
replacement.

TROUBLESHOOTING

Содержание RCS-3540C























Результаты поиска

Содержание RCS-3540C

Отзывы:

Бренды по названию

Популярные бренды

Ryobi RCS-3540C, Руководство оператора

Результаты поиска

Содержание RCS-3540C

Отзывы:

Бренды по названию

Популярные бренды