background image

7  

comply with standards, along with hearing protection.  

Failure to do so could result in objects being thrown into 

your eyes and other possible serious injuries.

APPLICATIONS

You may use this product for the purposes listed below:

 

Clearing leaves and other debris from your lawn

 

Keeping decks and driveways free from leaves and pine 

needles

 

Vacuuming leaves from your lawn

MIXING THE FUEL

This product is powered by a 2-Stroke engine and requires 

premixing petrol and 2-Stroke oil. The mixture should be at 

a 50:1 ratio.

NOTE: 

We recommend you use Ryobi synthetic 2-Stroke 

lubricant. Only use a quality synthetic 2-Stroke lubricant in 

your blower to ensure top performance and engine longevity.

TO MIX THE FUEL:

 

Pre-mix unleaded petrol and 2-stroke engine lubricant in 

a clean container approved for petrol.

 

This engine is certified to operate on unleaded petrol 

intended for automotive use with an octane rating of 91 

([R + M] / 2) or higher.

 

Do not use any type of pre-mixed petrol/lubricant from 

fuel service stations, this includes the pre-mixed petrol/

lubricant intended for use in mopeds, motorcycles, etc.

 

Avoid the use of Ethanol fuels or fuels containing 

Ethanol. The use of Ethanol fuels may result in damage 

to your engine.

 

Use synthetic 2-stroke lubricant only. Do not use 

automotive lubricant or 2-stroke outboard lubricant.

 

Mix 2% synthetic 2-stroke lubricant into the petrol. This 

is a 50:1 ratio.

 

Mix the fuel thoroughly and also each time before 

fueling.

 

Mix in small quantities. Do not mix quantities larger than 

usable in a 30-day period. A synthetic 2-stroke lubricant 

containing a fuel stabiliser is recommended.

 

1 litre   +  

20 ml 

 

2 litres   + 

40 ml   =

 

3 litres   +  

60 ml 

=  

  50:1

 

4 litres   +  

80 ml 

=

 

5 litres   + 

100 ml  =

INSTALLING THE VACUUM BAG

See Figures 3 - 4.

  Remove the nozzle and upper blower tube from the blower 

by twisting and removing from blower housing outlet.

  Unzip the vacuum bag and place the adaptor inside as 

shown. Push the vacuum bag adaptor through the opening 

opposite the zipper. The end of the adaptor with the tapered 

flange, will remain on the inside of the vacuum bag when 

installed properly.

  Align the raised slots on the vacuum bag adaptor with the 

raised locking tabs on the blower housing outlet; push the 

bag adaptor onto the housing. Twist to lock into place.

  Rotate the vacuum bag until the shoulder strap is upright.

 

Make sure the vacuum bag is zipped and closed before 

starting the unit.

INSTALLING THE VACUUM TUBES

See Figures 5 - 6.

 WARNING:

Rotating impeller blades can cause severe injury. Always 

stop the engine and ensure impeller blades have stopped 

rotating before opening the vacuum door or installing/

changing tubes. Do not put hands or any other object into 

the vacuum tubes while they are installed on the unit.

To install the vacuum tubes:

  Secure the upper and lower vacuum tubes together by 

aligning the raised locking tabs with the raised slots.

  Tap tube assembly on ground until the screw holes in lower 

tube are in the raised slot of the upper tube. Secure with 

supplied screws.

 

Depress door tab using a flathead screwdriver and open 

vacuum inlet door.

  Align tabs on housing with tube assembly. 

  Tighten screws on upper vacuum tube to secure to blower 

housing.

To remove the vacuum tubes:

 Loosen screws of the upper vacuum tube by turning 

counterclockwise.

  Remove the vacuum tube assembly from the blower 

housing.

  Close the vacuum inlet cover door securely.

OPERATION

 WARNING:

Do not allow familiarity with this product to make you 

careless. Remember that a careless fraction of a second is 

sufficient to inflict serious injury.

 WARNING:

Always wear eye protection with side shields marked to 

Содержание RBV26G













Отзывы: