Ryobi RBV254ON, Оригинальное руководство пользователя, Страница: 12 / 20

10
properly gapped and free of deposits in order to ensure
proper engine operation. The correct gap is 0.025 in.
(0.64 mm). To widen gap, if necessary, carefully bend
the ground (top) electrode. To lessen gap, gently tap
ground electrode on a hard surface.
5. Hand thread the new spark plug into the cylinder,
turning it clockwise.
6. Tighten with a socket. Torque to 216 in.lb. (24.40 Nm)
minimum, 264 in.lb. (29.82 Nm) maximum. Do not over-
tighten.
WARNING
Be careful not to cross-thread the spark plug. Cross-
threading will seriously damage the product.
TRANSPORTATION AND STORAGE
■ Stop the engine and allow it to cool before storing or
transporting.
■ Clean all foreign material from the product.
■ Drain all fuel from the tank into a container approved
for petrol. Remember to properly replace and tighten
the fuel cap.
■ Run the engine until it stops. This will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■ Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children and well away
from sources of ignition.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Do not store outdoors.
■ When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
or damage to the product.
■ Never carry or transport the product while the engine
is running.
■ Abide all government and local regulations for the
safety storage and handling of petrol.
Short term storage (less than 1 month)
■ Stop the engine, and allow it to cool before storing.
■ Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children and well away
from sources of ignition.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Do not store outdoors.
DESCRIPTION
See pages 1-4.
PARTS
1. Lower vacuum tube
2. Upper vacuum tube
3. Lock ring
4. Main housing
5. Vacuum bag adaptor
6. Leaf bag
7. Vacuum tube screw
8. Leaf nozzle
9. Throttle lock
10. Stop switch
11. Throttle trigger
12. Upper handle
13. Spark plug boot
14. Muffler
15. Starter grip and rope
16. Vacuum handle
17. Fuel cap
18. Choke lever
19. Primer bulb
20. Air filter base tab
21. Vacuum inlet door
22. Sweeper nozzle
23. Upper blower tube
24. Main housing outlet
25. Raised locking tab
26. Locking tab
27. Raised tab
28. Door tab
29. Vacuum door hinge
30. Unlock
31. Lock
32. Full choke
33. Half choke
34. Run position (no choke)
35. Air filter
36. Air filter cover
37. Spark plug
FEATURES
KNOW YOUR BLOWER/VACUUM
See figure 1-2.
The safe use of the product requires an understanding of
the information on the product and in this operator’s manual
as well as knowledge of the project you are attempting to
do. Before use of the product, familiarise yourself with all
operating features and safety rules.
BLOWER TUBE AND SWEEPER NOZZLE (LEAF
NOZZLE)
The blower tubes and sweeper nozzle (or leaf nozzle) can be
assembled and installed on the main housing using no tools.
SWEEPER NOZZLE
The sweeper nozzle allows for more area to be covered
during blower operation.
LEAF NOZZLE
The leaf nozzle allows for a higher air speed during blower
operation.
ENGINE
The blower has a powerful 25,4 cc engine with sufficient
power to handle tough blowing and vacuuming jobs.