Ryobi GS-400, Руководство по эксплуатации для владельца

Страница: 5 / 12

- 4 -
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read
through this OWNER’S MANUAL before using the prod-
uct.
WARNING! THIS PRODUCT IS DESIGNED TO SPRAY
CHEMICALS THAT MAY BE HARMFUL AND COULD
CAUSE SERIOUS PERSONAL INJURY IF INHALED OR
BROUGHT INTO CONTACT WITH THE USER.
WARNING! READ ALL INSTRUCTIONS BEFORE USE.
FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BE-
LOW AND/OR MISUSE OF THIS PRODUCT MAY SERIOUS
INJURY.
SAFETY INSTRUCTIONS
1. Wear long sleeve shirts, long pants, gloves, safety
glasses, respirator, and protection shoes.
2. Examine the sprayer overall before every time usage and
make sure the sprayer is no problem in usage.
3. Do not spray hot water, combustible, corrosive or highly
acidic liquids.
4. Do not face directly the upright of the pressure barrel
when pump, pressurize or dismantle the pump.
5. Do not expose the sprayer with pesticide under the sun.
6. Once the pressure barrel or rubber duct is damaged or
breach, do not pressurize to use.
7. Do not pressurize by means of mechanical devices, such
as air compressor.
8. Never fill tank above the top lone on the tank.
9. Before any maintenance, adjustment, cleaning or storing
the pump, make sure that pressure in the pump has been
released completely.
10. Before storing, wash thoroughly inside and outside of the
pump and barrel, then inject clean water into the pump
and spray for one minute so as to clean inside.
11. Do not store liquids in the tank.
12. Sprayer should be put in a safety place out of Children’s
reach.
13. Do not alter the sprayer or any components.
DESCRIPTION
1. Hose nut
2. Flow control hose nut
3. Flow control
4. Hose
5. Wand
6. Wand nut
7. Pump assembly
8. Tank
9. Pump handle
10. Flow control lever
11. Cone nozzle
12. Flow control cap
13. Pressure relief valve
14. Siphon tube
15. Hose insert
16. Threaded tank nipple
SPECIFICATIONS
GS-400 GS-600
Tank capacity 4littre 6littre
Working pressure 0.15 - 0.3Mpa 0.15 - 0.3Mpa
Hose length 1.2m 1.2m
Net weight 1.20kg 1.30kg
ASSEMBLY
HOSE TO TANK ASSEMBLY (Fig. 2)
1. Insert the siphon tube (14) into the hose insert (15)
otherwise sprayer will spray only air.
2. Lubricate the o-ring on the hose insert and then push into
the threaded tank nipple (16) until fully seated.
3. Screw hose nut (1) onto threaded tank nipple. Firmly
tighten it by hand.
FLOW CONTROL TO HOSE (Fig. 3)
1. Remove the flow control hose nut (2) from the flow
control (3) and slide over the hose (4).
2. Push the hose over the pointed end of the flow control
until it touches the threads.
3. Screw the flow control hose nut onto the flow control.
Firmly hand-tighten.
WAND TO FLOW CONTROL (Fig. 4)
1. Push the wand (5) into the flow control until it stops.
2. Slide the o-ring down until it touches the flow control.
3. Screw the wand nut (6) onto the flow control. Firmly hand
tighten.
IMPORTANT: TO ENSURE CORRECT ASSEMBLY, TEST
SPRAYER WITH WATER BEFORE USING.
FILLING THE SPRAYER
1. Remove the pump assembly (7) from the tank (8) by
turning counter-clockwise.
2. Prepare the spray solution following the instructions
listed on the chemical manufacturers’ label. Mix only the
amount of solution to be sprayed.
3. Screw the pump assembly back into the tank by turning
clockwise. Firmly hand tighten.
WARNING!
• Do not spray flammable, caustic (i.e. acids, chlorines and
bleach), corrosive, heated or self-heating solutions with
this sprayer.
• Never fill tank above the top line on the tank.
PRESSURIZING THE SPRAYER
1. Unlock the pump handle (9) by pressing down and
turning it until the hooks under the handle are positioned
on the slit. Be careful not to loosen the pump.
2. To create pressure, stroke up and down until you feel
difficult to stroke down.
3. Lock the pump handle back into the pump assembly by
pressing down and turning it.
WARNING! To prevent ejected pump assembly and/or
solution from striking and injuring you, never stand with your
face or body directly over the top of the tanks when pumping
or loosening the pump.
SPRAYING (Fig. 5)
1. To start spraying, squeeze the flow control lever.(10)
2. To stop spraying, release the flow control lever.
3. To spray continuously, squeeze the flow control lever and
slide forward to lock on.
4. If your sprayer has an adjustable cone nozzle (11), screw
the nozzle clockwise for a fine mist and counter-clockwise
for a coarse stream.
WARNING! (Fig. 6)
• DO NOT remove flow control cap (12)while spraying.
• ALWAYS wear long sleeve shirts, long pants, goggles,
gloves and durable shoes.