Ryobi EJ101, Руководство оператора, Страница: 6 / 20

Page 6
■
DRUGS, ALCOHOL, MEDICATION. Do not oper-
ate tool while under the influence of drugs, alcohol,
or any medication.
■
WHEN SERVICING USE ONLY IDENTICAL
RYOBI REPLACEMENT PARTS.
■
WARNING: TO AVOID POSSIBLE SERIOUS IN-
JURY, KEEP HANDS AND FINGERS FROM BE-
TWEEN THE MOTOR HOUSING AND SAW
BLADE CLAMP.
■
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan
them these instructions also.
SAVE THESE INSTRUCTIONS
RULES FOR SAFE OPERATION
BEFORE OPERATING
• Read the instructions carefully. Be familiar with the controls
and proper use of the unit.
• Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use the
unit, except for teens guided by an adult.
• Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in place
and secure. Replace blades that are cracked, chipped, or
damaged in any way. Make sure blades are properly
installed and securely fastened. Make sure the shoe is
secured properly and positioned as recommended. Failure
to so can result in personal injury to the operator and
bystanders, as well as damage to the unit.
• Be aware of the risk of injury to the head, hands and feet.
• Clear the work area before each use. Remove all objects
such as nails or wire which can contact the blade. Clear
the area of children, bystanders, and pets. At a minimum,
keep all children, bystanders, and pets outside a 50 feet
(15.2 m) radius; there still may be a risk to bystanders
from thrown objects. Bystanders should be encouraged
to wear eye protection. If you are approached, stop the
engine immediately.
• Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments or
repairs before using unit.
SAFETY WARNINGS FOR GASOLINE ENGINES
•
WARNING:
Gasoline is highly flammable, and its vapors
can explode if ignited. Take the following precautions:
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
• Always stop the engine and allow it to cool before filling
the fuel tank. Never remove the cap of the fuel tank, or add
fuel, when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.
• Mix and add fuel in a clean, well-ventilated area outdoors
where there are no sparks or flames. Slowly remove the
fuel cap only after stopping engine. Do not smoke while
fueling or mixing fuel. Wipe up any spilled fuel from the
unit immediately.
• Avoid creating a source of ignition for spilled fuel. Do not
start the engine until fuel vapors dissipate.
• Move the unit at least 50 feet (15.2 m) from the fueling
source and site before starting the engine. Do not smoke,
keep sparks and open flames from the area while adding
fuel or operating the unit.
WHILE OPERATING
• Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can kill. Operate this unit only in
a well ventilated area outdoors.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards, and ear/hearing
protection when operating this unit. Wear a face or dust
mask if the operation is dusty.
• Do not wear loose clothing, jewelry, sandals or go barefoot.
Secure hair above shoulder level.
• This unit has a clutch. The blade remains stationary when
the engine is idling. If it does not, have the unit adjusted
by an authorized service technician.
• Be sure the blade is not in contact with anything before
starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and unit
must be in a stable position while starting. See Starting/
Stopping Instructions.
• Use the right tool. Only use this tool for the purpose
intended.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
• Keep hands, face, and feet at a distance from all moving
parts. Do not touch the blade when it is rotating.
• Do not touch the engine or muffler. These parts get
extremely hot from operation. When turned off they
remain hot for a short time.
• Do not operate the engine faster than the speed needed
for the cut being made. Do not run the engine at high
speed when not cutting.
• If you strike a foreign object, stop the engine immediately
and check for damage. Do not operate before repairing
damage. Do not operate the unit with loose or damaged
parts.
• Stop and switch the engine to off for maintenance, repair,
or for changing blades.