manualshive.com logo in svg

Ryobi csb131, Руководство оператора

Поделиться
Скачать
Ryobi csb131 Скачать руководство пользователя страница 8

8

SPECIFICATIONS

UNPACKING

INSTRUCTIONS

Your circular saw has been shipped completely
assembled.

■

Carefully remove the tool and accessories from the
box. Make sure that all items listed in the packing list
are included.

■

Inspect the tool carefully to make sure no breakage
or damage has occurred during shipping.

■

Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
tool.

■

If any parts are damaged or missing, please contact
Ryobi Customer Service. Refer to the back page of
this manual for contact information.

Blade Diameter

7-1/4 in. (184 mm)

Blade Arbor

5/8 in. (16 mm)

Cutting Depth at 0

°

2-3/8 in. (60 mm)

Cutting Depth at 45

°

1-13/16 in. (46 mm)

Cutting Depth at 51.5

°

1-5/8 in. (41 mm)

Rating

120 volts, 60 Hz, AC

Input

13 amperes

No Load Speed

5500 RPM

Net Weight

12 lbs. (5.4 kg)

PACKING LIST

Circular Saw

7-1/4 in. (184 mm) Blade

Case

Rip Guide

Dust Nozzle Kit

Wrench

Warranty Card

Operator's Manual

WARNING:

If any parts are missing, do not operate this tool until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.

Содержание csb131























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды