background image

11

OPERATION

CHARGING A HOT BATTERY PACK

When using the product continuously, the batteries in the 
battery pack will become hot. You should let a hot battery pack 
cool down for approximately 30 minutes before attempting to 
recharge. When the battery pack becomes discharged and 
is hot, this will cause the green LED to come on instead of 
the red LED. After 30 minutes, reinsert the battery pack in 
the charger. If the green LED continues to remain on, return 
battery pack to your nearest Authorised Service Centre for 
checking or replacing.

NOTE: This situation only occurs when continuous use of 
the product causes the batteries to become hot. It does not 
occur under normal circumstances. Refer to CHARGING A 
COOL BATTERY PACK
 for normal recharging of batteries. If 
the charger does not charge the battery pack under normal 
circumstances, return both the battery pack and charger 
to your nearest Authorised Service Centre for electrical 
check.

WARNING:

Battery products are always in operating condition. 
Therefore, the switch should always be locked when not 
in use or carrying at your side.

TURNING THE SANDER ON ( I )/OFF ( O )

See Figure 3.

J

  Install the battery pack.

J

 To turn ON the sander: press down the ON ( I ) side of 

the switch.

J

 To turn OFF the sander: press down the OFF ( O ) side 

of the switch.

Fig. 2

Fig. 3

GREEN LED

BATTERY PACK

RED LED

YELLOW LED

CHARGER

ON ( I ) / OFF ( O ) SWITCH

ON ( I )

OFF ( O )

Содержание CRO1800
















Отзывы: