3
THANK YOU FOR BUYING A RYOBI SCREW DRIVER.
Your new screw driver has been engineered and
manufactured to Ryobi's high standard for dependability,
ease of operation and operator safety . Properly cared for,
it will give you years of rugged, trouble-free performance.
CAUTION
Carefully read through this entire operator's
manual before using your new screw driver.
Pay close attention to the Rules for Safe Operation,
Warnings and Cautions. If you use your screw driver
properly and only for what they are intended, you will
enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
GENERAL SAFETY RULES
WARNING
When using battery operated tools, basic safety
instructions should always be followed to reduce
the risk of fire, leaking batteries and personal
injury including the following. Read all these
instructions before operating this product and
save these instructions for future reference.
Keep work area clean.
Cluttered areas and benches
invite injuries.
Consider work area environment.
Do not expose
power tools to rain. Do not use power tools in damp
or wet locations.
Keep work area well lit.
Do not use power tools
where there is risk to cause fire or explosion.
Keep children away.
Do not let visitors touch the
tool. All visitors should be kept away from the area.
Dress properly.
Do not wear loose clothing or
jewellery, they can be caught in moving parts.
Use safety glasses.
Use face or dust mask if the
cutting operation is dusty. Also use ears protection to
reduce the risk of induced hearing loss.
Stay alert.
Watch what you are doing at all times.
Use common sense. Do not operate tool when you
are tired or under the influence of drugs or alcohol.
Store batteries or idle tools.
When not in use, tools
and batteries should be stored separately in a dry,
high or locked up place, out of the reach of children.
Ensure that battery terminal will not be shorted by
other metal parts such as screws, nail etc.
Secure work.
Use clamps or vice to hold the work.
It is safer than using your hand and it frees both
hands to operate the tools.
Do not overreach.
Keep proper footing and balance
at all times.
Do not force the tool.
It will do the job better and
safer at the rate for which it was intended.
Use the right tools.
Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use tools for purposes not intended.
Maintain tools with care.
Keep cutting tools sharp
and clean for better performance. Follow instructions
for lubrication and changing accessories.
Inspect tool cord periodically and if damaged
have it repaired by an authorized service facility.
Keep handles dry, clean and free from oil and grease.
Check damage parts.
Before further use of the tools, a
guard or other parts that is damaged should be carefully
checked to determine that it can operate properly and
perform its intended function. Any parts that is damaged
should be properly repaired or replace by an authorized
service center unless otherwise indicated in this
instruction manual. Have defective switches replaced by
an authorized service facility. Do not use the tool if the
switch does not turn it on and off.
Avoid accidental starting.
Be sure that the switch
trigger is in the locked or OFF position after use.
Do not carry the tool with a finger on the switch.
Disconnect tools.
Where the design permits,
disconnect the tool from its battery pack when not
in use, before servicing and when changing accessories.
Disconnect charger.
To reduce the risk of electric
shock, unplug the charger from the wall outlet before
attempting any maintenance or cleaning. Turning off
the controls will not reduce this risk.
Disconnect battery pack.
Disconnect battery pack
from tool before making any adjustments, changing
accessories or storing the tool. Depending on the design.
Charger maintenance
. Do not disassemble the
charger. Take it to a qualified service agent when
service or repair is required. Incorrect assembly may
result in risk of electric shock of fire.
Do not abuse the cord.
Never use the cord to carry
the charger. Keep cord away from heat, oil,
sharp edges or moving parts. Replace damaged
cords immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only
with the specified charger for the battery.
A charger that may be suitable for one type of battery
may create a risk of fire when used with another
battery. Use battery only with charger listed.
MODEL CHARGER NO.
CPD48N
720293001
The
screw
driver
should only be charged with the
RYOBI charger model 720293001.
The charger should not be used by young or
infirm persons unless supervised.
Young children
should be supervised to ensure they do not play with
the charger.
