background image

5

IMPORTANT INFORMATION FOR RECHARGING HOT

BATTERIES

CHARGING BATTERY PACK (Fig. 7, 8)

The battery pack for the tool has been shipped in a low charge

condition to prevent possible problems. Therefore, you should

charge it prior to use.

When using your tool continuously, the batteries in your battery

pack will become hot. You should let a hot battery pack cool down

for approximately 30 minutes before attempting to recharge.

1. While pressing the battery pack clip (7) gently slide out the battery  

    pack from driver drill. (Fig. 7)
2. Plug the battery charging adaptor (10) into a power outlet.
3. Plug the charger jack (11) into the charging socket on the battery 

    pack firmly. The LED charging status lamp turns to RED to 

    indicate it charging. (Fig. 8)
4. Once the charging completed, the LED charging status lamp  

    turns to GREEN. Remove the charging adaptor from the battery

    pack, and then plug off the charging adaptor.

NEVER COVER THE AIR VENTS SINCE THEY MUST ALWAYS

BE OPEN FOR PROPER MOTOR COOLING.
DRILLING IN WOOD

To prevent splintering around the drilled hole on the reverse side 

of the work piece, place scrap lumber beneath the material to be

drilled.

DRILLING IN METAL

Metals such as steel sheets, brass and aluminum sheets, stainless 

steel and pipe may also be drilled. Mark the point to be drilled with 

a nail or punch.

DRIVING SCREW

Match the bit and screw size to prevent damage to the screw head.

For removing screws, push the reversing switch to the left position.

After use, check the tool to make sure that it is in top condition.It

is recommended that you take this tool to a RYOBI Authorized

Service Center for a thorough cleaning and lubrication at least 

once a year.

DO NOT MAKE ANY ADJUSTMENTS WHILE THE MOTOR IS

IN MOTION.

ALWAYS REMOVE THE BATTERY FROM THE TOOL BEFORE

CHANGING REMOVABLE OR EXPENDABLE PARTS

(BIT...ETC.), LUBRICATING OR WORKING ON THE UNIT.

WARNING!

To ensure safety and reliability, all repairs should be performed by 

an 

AUTHORIZED SERVICE CENTER or other QUALIFIED

SERVICE ORGANIZATION.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

NOTE:

 

Batteries will not reach full charge the first time they are

charged. Allow several cycles for them to fully charge.

• Charge battery pack only with the charger provided.
• D

o not place charger in an area of extreme heat or cold. It will  

  work best at temperatures above 10°C and below 38°C.

• M

ake sure power supply is normal house voltage, 230 volts,  

  50Hz, AC only.

CAUTION!

OPERATING

MAINTENANCE

Содержание CLD-1880K









Отзывы: