background image

1

OPERATION

 

Unplug the sander.

WARNING:

Collected dust from sanding surface coatings such as 
polyurethanes,  linseed  oil,  etc.  can  self-ignite  in  the 
sander dust bag or elsewhere and cause fire. To reduce 
the risk of fire, empty the dust bag every 10-15 minutes 
while  sanding.  Never  store  or  leave  a  sander  without 
totally emptying its dust bag. Also follow the recommend-
ations of the coatings manufacturers.

  Remove the dust bag from the sander.

  Shake out the dust.

  Reattach the dust bag to the sander.

For a more thorough cleaning of the dust bag, remove dust 
bag from dust bag frame and shake out dust. Replace dust 
bag over frame then install dust bag assembly on sander.

CHANGING  THE  SANDING  SHEETS  AND 
PADS

See Figure 8. 

The sander is packed with sanding sheets and pads designed 
for a variety of uses. To change, simply pull the used sheet 
or pad off the base and attach the desired sheet or pad by 
pressing the it onto the base of the sander. 

PAPER PUNCH 

See Figure 9.

A paper punch template has been supplied with the sander 
for aligning and punching holes in sandpaper. The punched 

holes must align with the holes in the sander pad.

  Install sandpaper on the sander.

  Align the sander pad over the paper punch. 

  Push down on the sander.

Fig. 8

Fig. 9

hook-anD-Loop 

paD

paper punch

Fig. 7

Dust bag

bLower exhaust

EMPTyING THE DUST bAG

 

See Figure 7.

For more efficient operation, empty the dust bag when it is 
no more than half full to permit better air flow through the 
bag. Always empty and clean the dust bag thoroughly upon 
completion of a sanding operation and before storing.

Содержание CFS1503K















Отзывы: