![background image](http://html1.mh-extra.com/html/ryobi/art-3-ert-1150v/art-3-ert-1150v_user-manual_1507408006.webp)
2
English
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
RULES FOR SAFE OPERATION
Q
Reduce the risk of unintentional starting.
Make
sure switch is in the OFF position before plugging in
the tool.
Q
Use only the manufacturer ’s recommended
accessories.
Consult this operator ’s manual
for recommended accessories. Using improper
accessories may cause risk of injury.
Q
Never stand on tool.
Serious injury could occur
if the tool is tipped or if the blade is unintentionally
contacted.
Q
Periodically check for worn or damaged parts.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, loose mounting
brackets, and any other conditions that may affect
operation. A guard or any other part that is damaged
should be properly repaired or replaced. Before the
tool is used again, make sure that the repaired or
replaced part is operating properly and performing its
intended function.
Q
Direction of feed.
Feed work into a blade or cutter
against the direction of rotation of the blade or cutter
only.
Q
Never leave tool running unattended.
Turn the
power off. Do not leave tool until it comes to a
complete stop.
Q
Do not abuse cord. Never yank the cord to
disconnect it from the socket.
Keep the cord from
heat, oil, and sharp edges.
Q
Keep bits clean and sharp.
Sharp bits minimize
stalling. Dirty and dull bits may cause misalignment of
the material and possible operator injury.
Q
Keep hands away from cutting area.
Keep hands
away from the bit. Do not reach underneath table or
in the cutting path with your hands or fingers at any
time while tool is connected to power source.
Q
Firmly clamp or bolt your router table to a
workbench
so the router table surface is at
approximately hip height.
Q
Keep tool dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
Q
Stay alert. Never operate a power tool when tired
or while under the influence of drugs, alcohol or
medication.
Q
Do not use tool if switch does not turn it on
and off.
Have defective switches replaced by an
authorized service center.
Q
Always turn switch off
before disconnecting it to
avoid accidental starting.
Q
Save these instructions.
Refer to them frequently
and use to instruct other users. If you loan someone
this tool, loan them these instructions also.
WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
Q
lead from lead-based paints,
Q
crystalline silica from bricks and cement and other
masonry products.
Q
chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals, work in a well ventilated area, and
work with approved safety equipment, such as dust
masks that are specially designed to filter out microscopic
particles.
SPECIFIC SAFETY RULES FOR THE ROUTER
TABLE
Q
For your own safety, read this Router Table Operator’s
Manual and the Router Operator’s Manual before
operating the tool or router table.
Q
Feed workpiece against rotation of cutter.
Q
Use overhead guard.
Q
Do not use awkward hand positions.
Q
Keep fingers away from revolving cutter - use fixtures
when necessary.
Q
When using the router on the router table, the router
must be plugged into the on-board switched outlet.
FEATURES
KNOW YOUR ROUTER TABLE
Before attempting to use your router table, familiarize
yourself with all operating features and safety
requirements.
WARNING
If any parts are missing do not use your router
table until the missing parts are replaced. Failure
to do so could result in possible serious injury.
FENCE ASSEMBLY
Provides an adjustable surface to support and guide
work. The fence may be adjusted to compensate for the
stock reduced in the cut.
ART-3_EU manual_v2.indd Sec1:2
ART-3_EU manual_v2.indd Sec1:2
2010.3.30 5:55:19 PM
2010.3.30 5:55:19 PM