background image

10

OPERATION

ROUgH SURfACE ADAPTOR

See Figure 7.

By using the rough surface adaptor, you can use the AIRgrip 
feature to position the unit on many non-smooth surfaces, 
including brick and painted cinder block.

NOTE:

 The AIRgrip feature cannot be used with stucco or 

unpainted cinder block.

 

Place the adaptor over the AIRgrip base. 

 

Place  the  unit  against  the  desired  surface  and  press 
slightly to engage the seal.

 

Continue to hold the unit against the surface while press-
ing the on/off button.

 

Slowly release the unit when you hear a change in motor 
sound.

CAUTION:

Before releasing the unit, make sure the unit is securely 
adhered to the surface.

USINg THE MULTI-fUNCTION BASE

See Figures 8 - 9.

Hook-and-loop strap and push pin methods are available 
when the multi-function base is installed. To install, snap the 
base over the AIRgrip vacuum seal. 

HOOK-AND-LOOP STRAP:

 The strap can be used to attach 

the laser level to irregularly shaped objects such as pipes, 
boards, or metal grates.

 

Attach the strap to the multi-function base by threading it 
through the loops. The looped (or fuzzy) side of the strap 
should face the base.

 

Position  the  laser  level  against  the  surface  where  you 
want it mounted.

 

Wrap the strap around the object being mounted (pipe, 
board, etc.) and pass the end of the strap through the  
retaining loop. Pull to tighten.

 

Place the hooked end of the strap against the looped (or 
fuzzy) side of the strap and press together to secure. 

NOTE: 

To use the hook-and-loop strap to hang the unit from 

overhead, use the loops on top of the laser level housing.  

PUSH PINS:

 Push pins allow the laser level to be mounted 

to stucco and permeable surfaces.

 

Place the laser level on the surface where you want it 
mounted.

 

Align push pin with angled hole located on one side of 
laser level base and push in to secure.

 

In the angled hole on the other side of laser level base, 
secure the second push pin. 

Fig. 9

Fig. 8

Fig. 7

Содержание AIRgrip ProCross ELL0006















Отзывы: