RULES FOR SAFE OPERATION
4
SAFETY WARNINGS FOR
BATTERY TRIMMERS
•
Battery tools do not have to be plugged into
an electrical outlet; therefore, they are always
in operating condition. Be aware of possible
hazards, such as cutting attachment, even
when tool is not operating.
•
Use only the charging stand provided with
your unit. Do not substitute any other
charging stand. Use of another charging
stand could promote batteries to explode
causing possible serious injury.
•
Do not place battery units or their batteries
near fire or heat. They may explode causing
serious personal injury and damage to unit.
•
Do not charge unit in a damp or wet location.
•
Your unit should be charged in a location
where the temperature is more than 50˚F
(10˚C) but less than 100˚F (38˚C).
•
Do not disassemble the battery housing.
Battery should be recycled, consult your
local waste authority for information
regarding available recycling and/or disposal
options.
SAFETY WARNINGS FOR
CHARGING STANDS
•
Before using charging stand, read all
instructions and cautionary markings in this
manual, on charging stand, and product
using charging stand.
•
Do not expose charger to rain or snow.
•
To reduce risk of injury, charge only
sealed lead-acid rechargeable batteries.
Other types of batteries may burst, causing
personal injury and damage.
•
To reduce risk of damage to charger body
and cord, pull by the charger body, rather
than cord, when disconnecting the charger.
•
Make sure charger cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
•
Do not operate charger with a damaged
cord or plug. If damaged, replaced charger
immediately.
•
Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way. If the charger case is
damaged, replace the charger.
•
Do not disassemble charger. The charger is
not serviceable; disassembly may result in a
risk of electric shock or fire.
•
To reduce risk of electric shock, unplug the
charger from outlet before attempting any
maintenance or cleaning.
•
Do not use charger outdoors.
WHILE OPERATING
•
To avoid accidental starting, never carry your
trimmer with your finger on the trigger.
•
Wear safety glasses or goggles that are
marked as meeting ANSI Z87.1-1989
standards, and ear/hearing protection when
operating this unit. Wear a face or dust mask
if the operation is dusty. Long sleeve shirts
are recommended.
•
Wear heavy, long pants, boots and gloves.
Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair
above shoulder level.
•
The cutting attachment shield must always
be in place while operating the unit. Do not
operate unit without trimming line extended,
and the proper line installed. Do not extend
the trimming line beyond the length of the
shield.
•
Adjust the handle to your size to provide the
best grip.
•
Be sure the cutting attachment is not in
contact with anything before starting the unit.
•
Use the unit only in daylight or good artificial
light.
•
Use the right tool. Only use this tool for the
purpose intended.
•
Do not overreach. Always keep proper
footing and balance.
•
Do not force the unit. It will do the job better
and with less likelihood of a risk of injury at
the rate for which it was designed.
•
Always hold the unit with both hands when
operating. Keep a firm grip on both the
battery housing grip and D- handle.
•
Keep hands, face, and feet at a distance
from all moving parts. Do not touch or try to
stop the cutting attachment when it is
rotating.
•
Always stop the motor when cutting is
delayed or when walking from one cutting
location to another.
•
If you strike or become entangled with a
foreign object, stop the unit immediately and
check for damage. Do not operate before
repairing damage. Do not operate the unit
with loose or damaged parts.
•
Release the trigger, ensure the lock-off
button resets and allow the motor to stop
for maintenance, repair, or for changing the
cutting attachment or other attachments.
•
Keep unit clean of vegetation and other
materials. They may become lodged
between the cutting attachment and shield.
