ENVIRONMENTAL PROTECTION
Insert the large end of the hose into the blower
connection in the top of the motor housing (Fig. 17).
Fit the crevice tool to the vacuum hose (Fig. 18).
Ensure the power switch is turned off and plug in the
power supply.
Turn the motor on by flipping the switch to the “I” (ON)
position (Fig. 14).
The unit will now blow through the vacuum hose and can
be used to clear obstructions within the hose. (Fig. 19)
Verify that the power cord is disconnected from the outlet.
Undo the clamps and remove the top section from the
container (Fig. 21).
Clear all dirt or debris from the container and hose
(Fig. 22).
Disconnect the hose from the container (Fig. 20).
Once you have finished operation, flip the switch to the
‘O’ (OFF) position and unplug the power cord from the
power outlet. (Fig. 15)
IMPORTANT! CHANGE THE DUST FILTER REGULARLY.
IF THE MACHINE IS USED WITHOUT THE DUST FILTER,
THE MOTOR WILL BURN OUT AND THE WARRANTY
WILL BE VOIDED. ALWAYS KEEP SPARE FILTERS ON
HAND.
Recycle raw materials instead of disposing of as
waste. The machine, accessories and packaging
should be sorted for environmental-friendly
recycling.
If after a few seconds the hose continues to be blocked,
turn off the unit and clear the hose manually.
WARNING
4
SYMBOL
Class II equipment
Recycle
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
Please read the instructions carefully before
starting the machine.
Safety Alert
Volts
Hertz
Alternating Current
Watts
MAINTENANCE
Conformity
Install the dry filter over the filter cage with the flat end of
the filter towards the vacuum power head. Carefully push
filter in until it stops against the power head. (Fig.23 & 24)
Place filter retainer on top of cartridge filter over the raise
lip and tighten down by turning retainer clockwise, do not
over tighten. (Fig. 25 & 26)
Unlock and remove the filter retainer by turning retainer
handle anticlockwise.
Carefully hold and pull the dry filter up for removal.
(Fig. 27)
Clean the cartridge filter by gently tapping or brushing
dirt off. For optimal performance it is recommended to
regularly change this filter depending on level of use
(eg. 3-6 months).
INSTALLING AND CLEANING THE DRY FILTER
Removing And Cleaning Dry Filter (THIS FILTER IS
NOT WASHABLE)
Installing Dry Filter
Unplug machine from the power outlet before
performing maintenance.
NOTE:
Install cleaned or new filter into place as instructed above.
Follow instructions to remove dry dust filter first before
changing to foam filter.
Carefully slide foam filter down over the filter cage
making sure the whole cage is covered. (Fig. 9 & 28)
Carefully remove foam filter. (Fig. 29)
Use a mild soap and water solution to wash foam filter
and rinse with clean water. (Fig. 30)
Allow filter to air dry before installing and using again.
Installing Foam Filter
Cleaning Foam Filter
INSTALLING AND CLEANING THE FOAM FILTER
Unplug machine from the power outlet before
performing maintenance.
NOTE:
Содержание 0057838
