2. Introduction
Congratulations on your recent purchase of the Russound CA4.4pi multi-room controller. This four-zone, four-source, multi-room con-
troller is the heart of an affordable whole-house audio distribution system. Four high-current, stereo, power amplifiers are built into the
Russound CA4.4pi allowing simple connections to each speaker in the system. Each zone is operated by an intuitive, easy-to-use key-
pad that controls all the functions of the CA4.4pi. The keypads also have a built-in infrared receiver that allows remote commands for
your source equipment to be routed through the CA4.4pi.
The Russound CA4.4pi is built with pride. Fidelity, Reliability and Quality is the primary objective. Russound products are guaranteed to
provide years of enjoyment. The CA4.4pi is UL listed and CSA approved for your protection and peace of mind. Please take a moment
to fill out the warranty card and return it to Russound.
3. Possible System Configurations
3
4. Unpacking and Warranty Card
• Carefully unpack the CA4.4pi and keep the original carton and packing materi-
als for future moving, shipment or long-term storage. After opening the box,
please check for any visible signs of damage that were not apparent from the
outside of the box. If you do encounter what appears to be concealed damage,
please consult your Russound dealer before proceeding to further unpack or
install the unit.
• Make sure to save your sales receipt. Your receipt is extremely important to
establish the duration of your limited Warranty, and for insurance purposes.
• Warranty Card – The serial number appears on the rear panel of this unit near
the power cord. Copy the serial number onto your warranty card and mail it
back to Russound / FMP, Inc. 5 Forbes Road, Newmarket, New Hampshire,
03857, USA. Be sure to retain a copy and keep it in a safe place.
5. Getting Started
The following information will indicate some tools and materials necessary for a complete installation of the CA4.4pi:
• 4 twisted pair communication wire (commonly referred to as CAT 5). This wire will be used to connect the keypads in each zone to
the CA4.4pi controller. 16 Gauge minimum, 2 conductor CL3 rated wire. (Russound AW162CL3) This wire is used for direct connec-
tion between the CA4.4pi and your speakers.
• A small jewelers flat-head screwdriver.
• A medium sized flat-head screwdriver.
• Wire strippers and cutters.
• Electric drill and a 1/2" x 6 "drill bit.
• A steel-wire fish tape.
• A keyhole saw.
• Electrical junction boxes (6).
• A stud finder.
• A screwdriver (cordless recommended)
• Misc. hand tools, nails & screws.
• Cable staples.
If you have problems or you are not absolutely comfortable with what you are doing, consult a professional carpenter, electrician, or
system installer.
6. Basic Planning and Layout Considerations
• Where will the speakers be located?
• Where will the keypads be located?
• How will the wiring be routed to each location?
• Where is the source equipment located?
• Where is the CA4.4pi controller going
to be located?
ZONE 4
Guest Room
ZONE 2
Kitchen
ZONE 3
Master Bedroom
ZONE 1
Living Room
SOURCE EQUIPMENT
Family Room
CASSETTE
CD
TUNER
TUNER
CD
CASSETTE
DSS
DSS
(Audio Signal)
CA4.4pi
Controller
Speaker Wire Length
Gauge of Speaker Wire
10-100 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 AWG
100-150 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 AWG
Over 150 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 AWG
Connection Tips
• Disconnect all power cords before connecting to the CA4.4pi.
• Verify that all connections and polarity are correct.
• Keep all power cords away from all signal cables to prevent noise or humming.
• Choose reliable signal cables / patch cords.
• Label all wires with room location at both ends of the wire.
• Take your time!!! Don't panic about the number of wires;
simply connect one at a time.
