background image

distilled water. 

 

Too little water in the water tank. 

Fill water into the tank as 

per earlier instructions. 

Not Spraying 

There is not enough pressure or 

air inside. 

Press the spray nozzle by 

hand and push the spray 

button several times 

continuously. 

 

 

SERVICING THE APPLIANCE 

 

There are no user serviceable parts in this appliance. If the unit is not operating correctly, 

please check the following: 

  You have followed the instructions correctly

 

  That the unit has been wired correctly and that the wall socket is switched on.

 

  That the mains power supply is ON.

 

  That the plug is firmly in the mains socket. 

 

If the appliance still does not work after checking the above: 

- Consult the retailer for possible repair or replacement. If the retailer fails to resolve the 

problem and you need to return the appliance, make sure that:

 

  The unit is packed carefully back into its original packaging. 

  Proof of purchase is attached. 

  A reason is provided for why it is being returned. 

 

If the supply cord is damaged, it must be replaced by the manufacturer or an authorised 

service agent, in order to avoid any hazard. If service becomes necessary within the 

warranty period, the appliance should be returned to an approved Home of Living Brands 

(Pty) Limited service centre. Servicing outside the warranty period is still available, but will, 

however, be chargeable. 

 

CHANGING THE PLUG 

 

Should the need arise to change the fitted plug, follow the instructions below. 

This unit is designed to operate on the stated current only. Connecting to other power 

Содержание RHI002

















Отзывы: