Russell Hobbs RHF208P, Инструкция по эксплуатации

Страница: 8 / 12

THE MESH FILTER
• Wash the filter assembly (contains mesh filter) in warm soapy water.
• Leave it to air dry – do NOT refit it until it is completely dry.
THE HEPA FILTER
• The HEPA filter is responsible for cleaning the return air and requires careful handling.
• If the filter is covered in dust, tap it gently over some newspaper or on the rim of a rubbish bin
to dislodge the dust.
• If it is very dirty, soak it in warm soapy water for a few minutes, rinse under a running tap, remove
all traces of soap, then let it air dry – do NOT refit until it is completely dry.
REASSEMBLY
• Wait until everything is completely dry before reassembly.
• Lower the HEPA filter into the lid, locating the spindle into the bottom of the agitator. Make
sure it is fully seated in the lid – it may be necessary to turn it a bit to clear the lugs inside the lid.
• Lower the filter assembly over the HEPA filter, then turn it anti-clockwise to lock it into the lid
(it is a bayonet-type fitting).
• Turn the combined lid and filter assembly upside down.
• Align the mark on the lid with the (insert image unlock)marked on the bin.
• Lower the lid and filter assembly into the bin.
• Grip the bin lid with one hand, grip the bin with the other, and turn the lid of the bin to move
the
|
mark on the lid from the (insert image for unlock) on the bin round to the .
• Replace the bin in the cleaner – put the bottom in first, then push the top home. You will hear the
locks click into place.
• Check that it is secure.
CHECK THE OUTLET FILTER
• The outlet filter is located on the back of the vacuum cleaner.
• Press the lock down, pull the top of the cover away from the cleaner and lift the cover up and
off the cleaner.
• Ease the outlet filter out of the cleaner.
• If the filter is covered in dust, tap it gently over some newspaper or on the rim of a rubbish bin
to dislodge the dust.
• If it is very dirty, soak it in warm soapy water for a few minutes, rinse under a running tap, remove
all traces of soap, then let it air dry – do NOT refit until it is completely dry.
• When it is dry, replace it in the rear of the cleaner.
• The soft foam side of the filter should be towards the cover and the firm white side of the filter
should be towards the cleaner.
• Fit the lugs on the bottom of the cover into the slots in the cleaner and push the top of the cover
into the cleaner until it clicks into place
9
the mesh filter
• Wash the filter assembly (contains mesh filter) in warm soapy water.
• Leave it to air dry – do NOT refit it until it is completely dry.
the hePa filter
• The HEPA filter is responsible for cleaning the return air and requires careful
handling.
• If the filter is covered in dust, tap it gently over some newspaper or on the rim of a
rubbish bin to dislodge the dust.
• If it is very dirty, soak it in warm soapy water for a few minutes, rinse under a
running tap, remove all traces of soap, then let it air dry – do NOT refit until it is
completely dry.
reassemBly
• Wait until everything is completely dry before reassembly.
• Lower the HEPA filter into the lid, locating the spindle into the bottom of the
agitator. Make sure it is fully seated in the lid – it may be necessary to turn it a bit
to clear the lugs inside the lid.
• Lower the filter assembly over the HEPA filter, then turn it anti-clockwise to lock it
into the lid (it is a bayonet-type fitting).
• Turn the combined lid and filter assembly upside down.
• Align the mark on the lid with the
marked on the bin.
• Lower the lid and filter assembly into the bin.
• Grip the bin lid with one hand, grip the bin with the other, and turn the lid of the bin
to move the
|
mark on the lid from the on the bin round to the .
• Replace the bin in the cleaner – put the bottom in first, then push the top home.
You will hear the locks click into place.
• Check that it is secure.
lugs
HEPA
filter
spindle
filter
assembly
mark