I - SHIP PING AND PACK ING LIST
Package 1 of 2 contains:
1 - Energy Recovery Wheel Assembly
1 - Outdoor Fresh Air Hood with Filter
1 - Outdoor Exhaust Hood with Filter
1 - Platform Support Rail
1 - Bag Assembly
- Gasketing.
- Foot pads
- Hardware for standoff legs.
- Wiring harness
- Hardware for attachment to economizer.
Package 2 of 2 contains:
1 - Balancing Damper Assembly
2 - Side Filler Panels
4 - Hat Sections
II - SHIP PING DAM AGE
Check unit for shipping damage. Receiving party should
contact last carrier immediately if shipping damage is
found.
III - GEN ERAL
These instructions are intended as a general guide and do
not supersede local codes in any way. Authorities having
jurisdiction should be consulted before installation.
IV - RE QUIRE MENTS
When installed, the unit must be electrically wired and
grounded in accordance with local codes or, in absence of
local codes, with the current National Electric Code,
ANSI/NFPA No. 70.
V - AP PLI CA TION
Energy Recovery Ventilators (
ERV) are
used with units
equipped
with a return damper assembly.
These wheels
conserve energy by mixing warmer air with cooler air in the
following manner:
Re cov ery Mode
The Re
cov
ery Mode is ac
com
plished by two blow
ers
pro vid ing con tin u ous ex haust of stale in door air and
re
place
ment by equal amount of out
door air. En
ergy
re
cov
ery is achieved by slowly ro
tat
ing the En
ergy
Re cov ery Wheel (ERW) within the cas sette frame work. In
win
ter, the ERW ad
sorbs heat and mois
ture from the
ex haust air stream dur ing one half of a com plete ro ta tion
and gives them back to the cold, drier in take air sup ply
PAGE 1
dur ing the other half ro ta tion. In sum mer, the pro cess is
au to mat i cally re versed. Heat and mois ture are ab sorbed
from in
com
ing fresh air sup
ply and trans
ferred to the
ex
haust air stream. This pro
cess al
lows out
door air
ven ti la tion rates to be in creased by fac tors of three or more
with out ad di tional en ergy pen alty or increase in size of
heating or air conditioning systems.
VI - RIG GING UNIT FOR LIFT ING
1.
Maximum weight of unit is — 600 Lbs. (Crated)
2.
Remove crating. Then remove access panel (
See
Figure 1
) to retrieve bag assembly. Replace access
panel.
3.
All panels must be in place for rigging.
4.
Lifting lugs are supplied with the unit. Loosen machine
bolts and rotate lifting lug as shown in
Figure 1
.
VII - IN STAL LA TION
1.
Disconnect all power to rooftop unit.
ACCESS PANEL
LIFTING LUGS (4)
Figure 1
INSTALLATION INSTRUCTIONS
EN ERGY RE COV ERY WHEEL
INSTALLATION INSTRUCTIONS FOR ENERGY RECOVERY VENTILATOR (FIXED) USED
WITH TRANE ROOFTOP UNIT MODELS YCD/TCD 15 TO 25 TON UNITS
R46A-11TDW
MAY 2, 2005
SUPERCEDES 11-14-02
ETL Certified per UL 1995
and CSA 22.2
Energy recovery COMPONENT
certified to the AHRI Air-to-Air
E n e r g y R e c o ve r y V e n t i l a t i o n
Equipment Certification Program in
accordance with AHRI Standard
1060-2000. Actual performance in
packaged equipment may vary.
Содержание RRS Systems YCD
Страница 8: ...PAGE 8...
