background image

 

www.ruptela.com

 

[email protected] | +370 5 2045030

 

 1

 

Tachograph Solution

 

Quick Start Guide

 

Q

 

HCV5 

 

 

This quick start guide is only for the direct connection. For connection via the front interface, please refer 

to the 

user manual

. 

 

Make sure that you have: 

 

A vehicle with one of the following tachographs: 

o

 

Siemens VDO 1381 (versions higher than 1.3A)  

o

 

Stoneridge SE5000 (versions higher than 7.0) 

o

 

EFAS-4 or newer 

 

A computer with Windows 7/8/10 

 

An internet connection (or a

 

predownloade

Device Center

) 

 

A USB A to USB micro (Type B) cable  

 

tachograph harness

 (recommended) 

Device overview 
 
 

 

 

 

 

 

Indication LEDs  

Opening handles 

Grooves for zip-ties 

GNSS antenna port 

16 Pin port 

Micro USB port 

Audio port  

14 Pin port  

 

Indication LED patterns 

LED 

Pattern 

Description

 

GNSS 

Once every second 

Accurate signal 

Once every 0.4 seconds 

No signal 

Cellular 

Once every 4 seconds 

Connected to network and internet 

Once every second 

Connected to network, no internet 

Once every 0.2 seconds 

No signal 

Always on 

Link with the server is open 

Peripherals 

Always off 

No devices connected 

Once every 5 seconds 

One device connected 

Twice every 5 seconds 

Two devices connected 

Three times every 5 seconds 

Three devices connected 

All 

Once every 5 seconds 

Sleep mode 

Содержание HCV5 Series








Отзывы: