Copyright © 2013 Ruckus Wireless, Inc.
Published October 2013, Part Number 800-70507-001 Rev C
ZoneFlex R300 802.11n
Multimedia Wi-Fi Access Point
Quick Setup Guide
This
Quick Setup Guide
provides step-by-step instructions
on how to set up your Ruckus Wireless ZoneFlex Access
Point. After completing the steps described in this Guide,
you will be able to place the Access Point (AP) at your site
and provide wireless network access to users.
T
HIS
G
UIDE
IN
O
THER
L
ANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
.
Vous trouverez la version française de ce guide à l'adresse
suivante
https://support.ruckuswireless.com
.
こ の ガ イ ド の日本語版は
https://support.ruckuswireless.com
で ご覧 く だ さ い。
이
가이드의
한국어
버전은
웹
사이트
(
https://support.ruckuswireless.com
)
에서
확인하시기
바랍니다
.
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
B
EFORE
Y
OU
B
EGIN
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
•
User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents
.
•
Software Upgrades are available at
http://support.ruckuswireless.com/software
.
•
Open Source information is available at
http://opensource.ruckuswireless.com
.
•
Software License and Limited Warranty available at
http://support.ruckuswireless.com/warranty
.
P
ACKAGE
C
ONTENTS
•
ZoneFlex R300 Access Point
•
Mounting screws and anchors (2)
•
Security screw
•
Unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
This
Quick Setup Guide
S
ETUP
R
EQUIREMENTS
•
A computer running Windows 7 (procedures for other OS’s
are similar)
•
One or more of the following:
•
A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider
that brings Internet access to your site.
•
A network switch or a DSL/Internet gateway device.
•
Two Cat 5e Ethernet cables
•
An AC power adapter (sold separately), or
•
An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
S
TEP
1: C
ONNECT
THE
AP
TO
Y
OUR
C
OMPUTER
1
After removing your Ruckus Wireless AP from its package,
place it next to your computer.
2
Using an Ethernet cable, connect your computer’s network
port to the 10/100/1000 port on the AP.
3
Using the AC adapter (sold separately), connect the AP to a
convenient (and protected) power source.
•
Alternatively, connect the 10/100/1000 port to a PoE
injector or PoE switch for both power and network
connectivity.
4
Verify that the Power LED on the external enclosure is a
steady green.
S
TEP
2: P
REPARE
Y
OUR
C
OMPUTER
FOR
AP
S
ETUP
1
On your Windows 7 computer, configure your network
adapter from the
Local Area Connection
settings as follows:
•
Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
2
Edit the TCP/IPv4 address settings as follows:
•
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The
TCP/IPv4 Properties
dialog box appears.
3
Select
Use the following IP address
(if it is not already
selected) and then make the following entries:
•
IP address
: 192.168.0.22 (or any address in the
192.168.0.x network)
•
Subnet mask
: 255.255.255.0
•
Default gateway
: 192.168.0.1
Leave the
DNS server
fields empty.
4
Click
OK
to save your changes.
Your changes are put into effect immediately.
S
TEP
3: L
OG
I
NTO
THE
AP
As specified earlier, the AP should be directly connected to
your computer (through the Ethernet port) and powered on,
ready for setup.
1
On your computer, open a Web browser window.
2
In the browser, type this URL to connect to the AP:
https://192.168.0.1
NOTE:
The ZoneFlex R300 requires a minimum of Zone-
Flex firmware version 9.7 and above to operate.
IMPORTANT!
If the AP is deployed with a ZoneDirector, follow the
ZoneDirector Quick Setup Guide
, and connect the AP to your
local network.
NOTE:
The following procedures assume Windows 7 as the operating
system. Procedures for other OS’s are similar.
