Copyright © 2012 Ruckus Wireless, Inc.
Published June 2012, Part Number 800-70362-001 Rev C
ZoneFlex 7982 Dual Band
802.11n Multimedia Wi-Fi
Access Point
Quick Setup Guide
This
Quick Setup Guide
provides step-by-step instructions
on how to set up your Ruckus Wireless ZoneFlex Access
Point. After completing the steps described in this Guide,
you will be able to place the Access Point (AP) at your site
and provide wireless network access to users.
B
EFORE
Y
OU
B
EGIN
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
•
User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents
.
•
Software Upgrades are available at
http://support.ruckuswireless.com/software
.
•
Open Source information is available at
http://opensource.ruckuswireless.com
.
•
Software License and Limited Warranty available at
http://support.ruckuswireless.com/warranty
.
P
ACKAGE
C
ONTENTS
•
ZoneFlex 7982 Access Point
•
Mounting screws and anchors (2)
•
T-Bar clips and alignment spacer
•
Security screw
•
Regulatory flyer
•
This
Quick Setup Guide
S
ETUP
R
EQUIREMENTS
•
A computer running Windows 7(procedures for other OS’s
are similar)
•
One or more of the following:
•
A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider
that brings Internet access to your site.
•
A network switch or a DSL/Internet gateway device.
•
Two Cat 5e Ethernet cables
•
An AC power adapter (sold separately), or
•
An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
S
TEP
1: C
ONNECT
THE
AP
TO
Y
OUR
C
OMPUTER
1
After removing your Ruckus Wireless AP from its pack-
age, place it next to your computer.
2
Using an Ethernet cable, connect your computer’s net-
work port to one of the two ports on the AP.
3
Using an AC adapter (sold separately), connect the AP to
a convenient (and protected) power source.
•
Alternatively, connect the 10/100/1000 POE port to a
PoE injector or switch for both power and network
connectivity.
4
Verify that the Power LED on the external enclosure is a
steady green.
S
TEP
2: P
REPARE
Y
OUR
C
OMPUTER
FOR
AP
S
ETUP
1
On your Windows 7 computer, configure your network
adapter from the
Local Area Connection
settings as fol-
lows:
•
Start > Control Panel > Network and Sharing Cen-
ter > Change Adapter Settings
2
Edit the TCP/IPv4 address settings as follows:
•
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The
TCP/IPv4 Properties
dialog box appears.
3
Select
Use the following IP address
(if it is not already
selected) and then make the following entries:
•
IP address
: 192.168.0.22 (or any address in the
192.168.0.x network)
•
Subnet mask
: 255.255.255.0
•
Default gateway
: 192.168.0.1
Leave the
DNS server
fields empty.
4
Click
OK
to save your changes.
Your changes are put into effect immediately.
S
TEP
3: L
OG
I
NTO
THE
AP
As specified earlier, the AP should be directly connected to
your computer (through one of the Ethernet ports) and
powered on, ready for setup.
1
On your computer, open a Web browser window.
2
In the browser, type this URL to connect to the AP:
https://192.168.0.1
3
Press <Enter> to initiate the connection. When a security
alert dialog box appears, click
OK/Yes
to proceed.
4
When the
Ruckus Wireless Admin
login page appears,
enter the following:
•
Username
: super
•
Password
: sp-admin
5
Click
Login
.
IMPORTANT!
If the AP is deployed with a ZoneDirector, follow the
ZoneDirector Quick Setup Guide
, and connect the AP to
your local network.
PoE In
DC input
NOTE:
The following procedures assume Windows 7 as the oper-
ating system. Procedures for other OS’s are similar.
IMPORTANT!
Write down all of the currently active settings so you can
restore your computer to its current configuration later
(when this process is complete).