Ruckus Wireless ICX 7850 Series Скачать руководство пользователя страница 40

Страница: 40 / 102

Ruckus ICX 7850 Switch Hardware Installation Guide

Part Number: 53-1005580-01

Mounting the Device

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

FIGURE 21

Attaching the Rear Brackets to the Rack Posts

Flush-Rear (Recessed) Mounting the Device in the Rack

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device.

NOTE

The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

“Attaching the Front Brackets to the Rear of the Device”

on page 31

“Attaching the Extensions to the Front of the Device”

on page 31

“Installing the Device in the Rack”

on page 32

“Attaching the Rear Brackets to the Extensions at the Front of the Device”

on page 33

“Attaching the Rear Brackets to the Front Rack Posts”

on page 34

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

Содержание ICX 7850 Series







































































































Результаты поиска

Содержание ICX 7850 Series

Отзывы:

Похожие инструкции для ICX 7850 Series

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7850 Series, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7850 Series

Отзывы:

Похожие инструкции для ICX 7850 Series

Бренды по названию

Популярные бренды