Description
Part Number
Quantity
48.25" Shelf (labeled A)
3G62
2
48.25" Shelf (labeled B)
3J62
1
26.25" Shelves (labeled A)
3G60
3
26.25" Shelves (labeled B)
3J60
4
47.5" Uprights
3G64
6
25" Upright Extension
3G65
3
Upright Connector Clip
5E19
3
Brackets
3G63
19
48" Overlapping Hang Rails
3G67
1
36" Overlapping Hang Rails 3G66
2
Clothes Rod Hangers
3G68
10
48" Inner Clothes Rod
3G76
1
48" Outer Clothes Rod
3G77
1
26" Inner Clothes Rod
3G72
1
26" Outer Clothes Rod
3G73
1
22" Rail Covers
3J57
5
Shoe Shelf Brackets
3F58
4
The following parts are packed together in a hardware bag:
Screws
1603168
24
0.5" Drywall
Anchors
3J65
18
Anchor Push Pin
3J66
1
2" Rail Covers
3J55
2
Clothes Rod End Caps
3G71
8
6–10 ft. Adjustable Closet System
Please read through the instructions completely and check that you have all parts before beginning.
Depending on the configuration you choose to install, you may not use all of the components.
©
2011 Rubbermaid Incorporated, Huntersville, NC 28078-1807 • 1-888-895-2110
www.rubbermaid.com
3P40
Tools Needed
for Installation
1/8"
3/8"
L83P40L0RV2
optional
4
Install Upright Extensions
Slide in upright connector
Slide one end of the upright
connector into the top two
notches of the short upright.
Slide in other end to upright
Slide the other end of the upright
connector into the bottom two notches of
the long upright. Use a level to position
the short upright and mark the position of
the top & bottom screw holes.
Fasten screws
Drill 1/8" pilot hole and fasten both screws (use wall anchor and 3/8"
bit if there is not stud). To position the second upright extension, use
22" rail cover to ensure proper spacing is parallel from the first
upright extension.
Hint: Install these in the area of the closet where you would be most likely to install accessories (sold separately) or shelving closer to the floor.
Use shoe shelf brackets (included) to create additional storage space.
A
B
C
D
“A” shelf sits in
front notch
“B” shelf sits in
back notch
Bracket
Secure shelves with bracket locks
After all shelves are positioned properly, lock
shelves into brackets by sliding the plastic
locking clip towards the back wall. It will
"snap" into locked position.
Place shelves onto brackets
Shelf labeled “A” sits in front notch of bracket. Shelf labeled “B”
sits in back notch. Be sure each shelf
slides back as far as possible before locking shelves into brackets. If overlapping three sections of
shelving, use two “A” sections and one “B” section, placing “A” sections on the outside and spanning the
gap with “B” sections. For four or more overlapping sections, continue alternating between “A” and “B”
sections, placing “A” shelves on brackets before “B” shelves.
D
C (2)
Hint: If shelves are installed in the incorrect notch, shelving weight capacity could be lessened.
5
Install Brackets and Expanding Shelves
A
Hint: When overlapping sections of shelving, shelves labeled “A” must be placed
onto brackets before shelves labeled “B”.
Insert brackets
Insert brackets into uprights at desired locations.
Note: Install brackets and shelving at the top
first and work down. Brackets will not fit into
upper two slots of each upright.
B
on top
Overlapping shelves
Shelves are fully adjustable and require no cutting.
To adjust width, overlap the shelves making sure
the shelf labeled “A” is placed first on the brackets
and the shelf labeled “B” is placed on top of “A”.
Install shelves into brackets
Confirm that the bracket locks are unlocked
and install shelving making sure that the
“nose” of the bracket is projecting out through
the front edge of the shelf.
Note: For maximum
weight capacity, do not insert brackets into
bottom slots of upright.
A
B
C (1)
6
Install Adjustable Clothes Rods
End cap
fit on outer
clothes rod
End cap
fit on inner
clothes rod
3" max.
Press firmly
into place
Install rod hanger
Install rod hanger into bottom of
bracket by tilting it backward until
it locks in place.
Note: be sure to
press rod hangers firmly into place
for proper installation.
Adjust rod length
Rods can be used separately or
telescoped together. 48" telescope
up to 8' and 26" telescope up to 4'.
Add end caps
Place end caps on the end of
each clothes rod. End caps will
fit either diameter of rod (As
shown above).
Secure rod and hanger
After expanding clothes rod to
desired length, place into rod
hangers and press down to snap
into place.
Note: do not extend
more than 3" past rod hangers.
A
B
C
D
