6
Table 3
- Ring Count Settings
Table 2
- Address DIP Switch Settings
Internal DIP Switch
(S202)
Internal DIP Switch
(S203)
Figure 3 -
TIF 4000 Internal DIP Switch Locations
Zeus units use a 1-8 address scheme for their ports
(e.g. ports 1-8 have address 1-8, ports 9-16 have
addresses 1-8, etc...). CS9xxx systems use a 1-10
scheme for port address (e.g. ports 1-10 have address
1-10. ports 11-20 have addresses 1-10, etc...).
NOTE
: You must set the card address before you
put the card into the Frame.
To set the address for ADAM, ADAM CS, or Zeus
systems, do the following:
1
Determine the port number that will be used
for the TIF-4000.
2
Locate the port number and its corresponding
address in Table 1.
3
Determine the DIP switch settings by looking
up the address determined in the previous
step in Table 2.
4
Set the DIP switches on the back of the unit.
To set the address for CS 9xxx systems, do the
following:
1
Determine the intercom port (audio channel
number) that will be used for the TIF-4000.
2
For port numbers ending in 1 through 9, the
address is the last digit of the port number. If
the last digit is zero, use 10 as the address
number.
3
Determine the DIP switch settings by looking
up the address in Table 2.
4
Set the DIP switches on the back of the unit.
FULL DUPLEX METHOD SWITCH 8 (S201)
Switch 8 (S201) controls the method by which full
duplex operation is implemented in the unit. This
switch only works if full duplex mode is set via internal
DIP switch (S202), switch 7 (factory default setting for
Switch 7 is OFF, full duplex mode). If switch 8 is in the
open position, then the unit will be forced into full
duplex mode all the time. If switch 8 (S201) is in the
closed position, then the unit will be forced into full
duplex mode only when audio is present.
When using full duplex mode, users may hear an
increased amount of echo on the line. This may be
more pronounced when the TIF-4000 is forced into full
duplex mode all of the time (switch 8 open) rather only
when audio is present (switch 8 closed).
Internal DIP Switch (S202)
Internal DIP switch (see Figure 3) is accessed by
removing the card from the frame
RING COUNT
Switches 1 and 2 determine the number of rings
before the unit auto answers. The ring count is
approximate. The switches have no effect unless
switch 1 on the rear panel DIP switch bank is in the
down position. To set the ring count, see Table 3.
DTMF OR PULSE DIAL SELECTION
Switch 3 sets the dialing mode to either Dual Tone
Multi-Frequency (DTMF, also known as touch tone) or
Pulse. When the switch is in the OFF position, DTMF
dialing is selected. When the switch is in the ON
position, Pulse dialing is selected.
POINT-TO-POINT SEIZE
Switch 4 turns ON and OFF the Point-to-Point Seize
feature. When the switch is in the OFF position, the
normal line seize operation (via the keypanel) is
selected. When the switch is in the ON position a line
will be seized immediately upon the designated TIF-
4000’s talk key being pressed via the keypanel.
l
a
c
i
g
o
L
l
e
n
a
p
y
e
K
r
e
b
m
u
N
s
g
n
i
t
t
e
S
h
c
t
i
w
S
p
i
D
4
W
S
5
W
S
6
W
S
7
W
S
1
d
e
s
o
l
C
n
e
p
O
n
e
p
O
n
e
p
O
2
n
e
p
O
d
e
s
o
l
C
n
e
p
O
n
e
p
O
3
d
e
s
o
l
C
d
e
s
o
l
C
n
e
p
O
n
e
p
O
4
n
e
p
O
n
e
p
O
d
e
s
o
l
C
n
e
p
O
5
d
e
s
o
l
C
n
e
p
O
d
e
s
o
l
C
n
e
p
O
6
n
e
p
O
d
e
s
o
l
C
d
e
s
o
l
C
n
e
p
O
7
d
e
s
o
l
C
d
e
s
o
l
C
d
e
s
o
l
C
n
e
p
O
8
n
e
p
O
n
e
p
O
n
e
p
O
d
e
s
o
l
C
9
d
e
s
o
l
C
n
e
p
O
n
e
p
O
d
e
s
o
l
C
0
1
n
e
p
O
d
e
s
o
l
C
n
e
p
O
d
e
s
o
l
C
E
T
O
N
!
y
l
n
o
s
e
s
s
e
r
d
d
a
m
e
t
s
y
s
x
x
x
9
S
C
r
o
f
s
i
a
e
r
a
d
e
d
a
h
S
:
s
g
n
i
R
f
o
#
1
W
S
2
W
S
1
F
F
O
F
F
O
2
N
O
F
F
O
4
F
F
O
N
O
8
N
O
N
O
Internal DIP
Switch (S201)