9
Setting Audio Levels
Audio levels to the intercom matrix and to the telephone
line can be adjusted via the trim pots located on the front
panel.
Setting audio levels to intercom matrix
Adjustment may be made via the front panel control (see
Figure 1). To adjust the control use a small flat blade
screwdriver or trimpot adjustment tool. Initially set the front
panel level control for mid range. Have the caller talk at
their normal level and adjust the control for the best audio
quality while avoiding going into the red section of the
audio meter (to Matrix) located on the front panel.
Setting audio levels to telephone line
Adjustment may be made via the front panel control (see
Figure 1). To adjust the control use a small flat blade
screwdriver or trimpot adjustment tool. Initially set the front
panel level control for mid range. Talk at your normal level
and adjust the control for the best audio quality while
avoiding going into the red section of the audio meter (to
Telephone) located on the front panel.
Configuring for Country’s Telephone System
The TIF 2000 should be configured to work with the
telephone system to which it is connected. Each country or
area of the world has unique signaling differences that could
cause erratic operation of the TIF 2000 if it is not properly
configured. If the system you intend to connect is not
currently supported, you may request a configuration using
the form located in the back of this manual.
To configure the unit for use with a specific country’s
telephone system do the following:
Note: ADAMedit and ZEUSedit must be configured to
allow firmware downloads.
1. Connect the TIF 2000 to the intercom system.
2. Run the ADAM Edit or ZEUS Edit software and go to the
keypanel software versions screen. This is located under
the Status menu. Go to
|Status| |Software Versions|
|Keypanels|
.
3. Click on the entry for the TIF 2000 you wish to config-
ure.
4. The configurations are in a self extracting archive on the
included floppy disk. Extract and copy these files to a
known location on the computer connected to the
intercom matrix
5. Press
CTRL
+
SHIFT
+
D
to start the software down-
load process. A download screen should appear.
6. Select the location that you copied the files to in step 4
and select the file corresponding to the country needed.
7. Click on the OK button.
Once the software versions window reappears, the process is
complete.
The status reported for the TIF 2000 contains a number
corresponding to the country configuration. This is reported
as LOCALE = XX where XX is a specific number for each
country. The current possible configurations are:
LOCALE #
Country or Countries
0
North America, Korea, Taiwan
1
Belgium
2
France
3
Germany
4
United Kingdom (UK)
5
Italy
6
Japan
7
Netherlands
8
Norway
9
Not Used
10
Singapore
11
Brazil, Sweden
12
Ireland
CUST
Custom Configuration
OPERATION
Operation From A Keypanel
The TIF 2000 is operated from the intercom keypanels, and
from the dial pad on the telephone at the remote end of the
line. Any keypanel with a keypad may use a TIF 2000. All
that is necessary is to program a key to talk to the TIF 2000,
as if it were a keypanel. The alpha numeric display or tally
LED for that key then provides information about the phone
line. A solid display or non illumined LED indicates a line
which is not in use. A slow flash indicates a line which is in
use (off hook). A rapidly flashing display or LED indicates
a line which is ringing. In addition, the alpha numeric
display will display digits as they are dialed, and the LED
will flash for each digit.
Note: Displayed tallies will be different if the “Don’t
generate tallies for TIF or trunk use” option has been
selected in |Options| |Intercom Configuration|.
Programming a key to use the TIF 2000
To use the TIF 2000, either to answer a call, or to call out,
you first need to program a key to talk to the TIF 2000. This
is accomplished in the same manner as programming a key
to talk to a key panel. To program a key by port number,
enter NUM-nnn-PGM-t, where NUM is the number 1 key,
nnn is the port number of the TIF 2000 you want to use, and
t is any talk key. In general, you will also need to use the
listen key, so it should be assigned as either AF (auto
follow), or AL (auto listen).