background image

7

Introduction

 This manual describes the installation and opera-
tion of the TM-2000/MTM-2000 Trunk Master
and Mini-Trunk Master, SWP-2000 Switch Over
Panel, and ICP-2000 Interconnect Panel.

TM-2000/MTM-2000 Description

The RTS Trunking System manages intercommu-
nications between separate intercom systems
using intercom ports that have been reserved and
interconnected between the intercom systems.
Keypanels or other data devices can then commu-
nicate with various destinations in other intercom
systems via the reserved intercom ports.  (This is
different from bus expansion, in which the bus
system of two or more frames are interconnected
to form one larger system.)

The RTS Trunking System consists of an RTS
Model TM-2000/MTM-2000 and one or more
RTS Model ICP-2000 Inter-Connection Panels,
depending on the number of intercom systems to
be trunked.  A backup TM-2000 / MTM-2000
may also be added to prevent downtime in the
event of a failure of the main master control unit.
When both main and backup control units are
used, an RTS Model SWP-2000 Switch Over
Panel is required.

Front Panel Features

1.

Status indicators for power, hard drive, fan,

system temperature

2.

Front security panel

3.

Cooling fan

4.

Power switch (front)

5.

System reset switch

6.

Status indicators (from top to bottom):

Power, Hard Disk, Fan Failure, Over Tem-
perature 1, Over Temperature 2

7.

Floppy drive *

8.

System over temperature alarm silence

switch.

9.

CD-ROM drive *

* Used only for factory service

.

Rear Panel Features

1.

Power supply fan.

2.

AC power connector

3.

AC voltage selector switch

4.

Power switch (rear)

5.

Keyboard and mouse connectors*

6.

Parallel port connectors. See note below

7.

Serial (COM) port connectors. See note
below

8.

Card slots containing: (a) RS-485 communi-
cation card(s) using SCSI type II connector.
See note below.  (b) Networking connector
using RJ-45 connector.  See note below.  (c)
Video monitor connector* using 15-pin D-Sub
connector.

* Used only for factory service

.

NOTE:  The exact location of cards and connector
designations can vary from unit to unit.  The
diagram provided is for general feature locations
only.  Follow the designated labels found on your
particular unit(s).

TM

TM-2000

2

1

3

4

5

6

7

8

9

1

2

3

4

5

6

7

8

With Security Cover

With Security Cover

Figure 1.  TM-2000 front panel features.

Figure 2.  TM-2000 rear panel features.

Содержание ICP-2000























Отзывы: