RTA 460ETCUS Скачать руководство пользователя страница 17

Страница: 17 / 80

Real Time Automation, Inc.

1-800-249-1612

Allen-Bradley PLC Configuration

Click the

Allen-Bradley PLC

button to access the configuration page.

Select which

Network Interface

to use for this Allen-Bradley PLC connection. If using single port

hardware, the Network Interface will default to Ethernet port only.

Delay Between Messages

: Enter the length of time to delay between read and write scan line

requests (ms).

Response Timeout

: Enter the amount of time the gateway should wait before a timeout is

issued for a read/write request (ms).

Delay Between Connect Attempts

: Enter the amount of time the gateway should wait between

attempts to connect to the PLC.

Dependency Protocol

: If enabled, the Allen-Bradley PLC communication will stop if

communication to the selected protocol is lost.

Содержание 460ETCUS

















































































Результаты поиска

Содержание 460ETCUS

Отзывы:

Похожие инструкции для 460ETCUS

Бренды по названию

Популярные бренды

RTA 460ETCUS, Руководство пользователя

Результаты поиска

Содержание 460ETCUS

Отзывы:

Похожие инструкции для 460ETCUS

Бренды по названию

Популярные бренды