RTA 460BCDFM-NNA1 Скачать руководство пользователя

Страница: 58 / 66

Real Time Automation, Inc.

1-800-249-1612

Connected and Running

–

The gateway is connected to all the DF1 slaves.

Error: Timeout

–

No DF1 scan lines are configured under an enabled slave.

Or, one or more enabled DF1 slaves are missing.

Verify DF1 device for correct Destination ID.

Verify that Port Settings used match the DF1 slave(s) that the gateway is communicating with.

Verify wires for specific port settings.

Dependency Protocol Faulted

–

The dependent protocol is missing causing the communication to

stop.

Unknown: First Scan Not Complete

–

Multiple scan lines are set up for the device and the gateway

has not completed all the scan lines for the first time.
5)

Fatal Error: Couldn’t Open Hardware Port –

The serial port selected on the DF1 Master

Configuration page is not configured.

Fatal Error: No Configuration

–

No DF1 slaves are enabled though a serial port is enabled.

LED Status

- This is the status for

All Slaves,

or the specific slave selected.

Solid Green (Connected)

–

The gateway is connected to all the DF1 slaves that are configured and

enabled.

Flashing Green (Not Connected)

–

No DF1 slaves are enabled/configured.

Verify DF1 settings and ensure that the

Enable

checkbox is checked for the appropriate slave(s).

Flashing Red (Connection Timeout) - The gateway cannot open a connection to one or more of the
enabled DF1 devices.
a)

Verify DF1 Communication Command.

Verify DF1 Destination IDs.

Verify port settings used match the DF1 slave that the gateway is communicating with, including
Protocol Mode and Frame Verification.

Verify wires for specific port settings.

Flashing Red (Empty Scan List) - One or more enabled DF1 slaves have no scan lines configured.

Flashing Red (Communication not attempted yet)

–

(Specific slave only) No reads are configured and

data needed for writes isn’t valid yet.

Flashing Red (Dependency Error) - The dependent protocol is missing causing the communication to
go to inactive.
a)

The other protocol must be

Connected

Содержание 460BCDFM-NNA1



































































Результаты поиска

Содержание 460BCDFM-NNA1

Отзывы:

Похожие инструкции для 460BCDFM-NNA1

Бренды по названию

Популярные бренды

RTA 460BCDFM-NNA1, Руководство пользователя

Результаты поиска

Содержание 460BCDFM-NNA1

Отзывы:

Похожие инструкции для 460BCDFM-NNA1

Бренды по названию

Популярные бренды