RST Milo Fire Table Скачать руководство пользователя страница 13

12

INSTALLATION SAFTEY GUIDLINES

1.  Installation and repair should be done by a qualified service person. The 

appliance should be inspected before use and at least annually by a qualified 

service person. More frequent cleaning may be required as necessary. It is 

imperative that control compartment, burners, and circulating air passageways 

of the appliance be kept clean. 

2.  Carefully inspect for shipping damage. If any parts are damaged, call the dealer. 

3.  Correct installation and proper placement of the unit and decorative media 

is crucial to the safe performance of the unit. See installation instructions for 

further information. 

4.  Ensure that the unit is installed in such a manner that the vent opening at 

the base of the unit remains obstacle-free at all times and during all weather 

conditions. 

5.  Due to high temperatures, the unit must be located out of traffic areas and 

away from combustibles.

OPERATING THE UNIT SAFELY AND CORRECTLY

1.  This appliance is only intended for operation in temperatures above 320 F.

2.  When shutting the unit down make sure to turn the control valve FULLY OFF. 

3.  Children MUST be carefully supervised when they are in the area of this 

appliance. 

4.  DO NOT sit or place any part of the body, clothing, or other flammable materials 

on or near the unit surrounding. Children and adults should be alerted to the 

hazard of high surface temperatures and should stay away to avoid burns or 

clothing ignition. 

5.  Every time you use the unit, make sure that: 

a. The area around the unit is clear and free from combustible materials, gasoline, 

and other flammable vapors and liquids. 

b. There is no blockage of the airflow through the vent openings located on the 

bottom of the unit. 

c.  The hose is inspected (if applicable). See the SAFE USE AND MAINTENANCE OF 

PROPANE-GAS CYLINDERS section. 

6.  WARNING: HOT WHILE IN OPERATION AND FOLLOWING OPERATION. Serious 

injury can occur! Do NOT throw trash, paper, or other flammable materials in 

the unit. DO NOT leave in operation when unattended. DO NOT OPERATE THIS 

UNIT IN THE RAIN. 

7.  SOLID FUEL MUST NOT BE BURNED IN THE UNIT.

8.  DO NOT continue using if you smell unusual odors or have headaches, nausea, 

or dizziness. 

9.  DO NOT store any combustible materials, gasoline, and any other flammable 

vapors/liquids in the vicinity of this unit. Provide adequate clearance for 

servicing and operation. 

10. Matches, paper, garbage, or any other material must not be thrown into the 

unit or into the flame.

11. DO NOT use the unit if any part of it has been underwater. Immediately call a 

qualified professional service technician to inspect the set and to replace any 

part of the control system that has been underwater. 

Содержание Milo Fire Table























Отзывы: